sq11 camera 3d models
108338 3d models found related to sq11 camera.prusaprinters
A simple case for the SQ11 camera. Recommended material: PETGV1 - Looser grip, good for stationary applicationsV2 - Sturdier grip of the camera, hard for it to fall out
thingiverse
SQ11 Camera Thick TPU.stl is similar to the shell model, but redesigned with double thickened walls and a shorter stiffer latch for use with TPU filaments. This is the clear print in the photos. ...I strongly recommend this version if you can print...
thingiverse
*Prints in TPU or Ninja Flex* Made this for my little mini SQ11 camera. Use a strap or some wire ties to mount in a variety of ways.. Camera will also fit into sleeve multiple ways. Sleeve is sized for easy install and removal but can be resized...
prusaprinters
Vidroc SQ11 camera mount Update - Added a BT-50 nose cone mod for this camera. - You have to print the nose cone with supports. - Either glue or screw the camera mount into the notch in the nose cone Simple set of mounts that allow you to mount a...
thingiverse
Vidroc SQ11 camera mount Update - Added a BT-50 nose cone mod for this camera. - You have to print the nose cone with supports. - Either glue or screw the camera mount into the notch in the nose cone Simple set of mounts that allow you to mount a...
thingiverse
... camera in the four notches. ... For the Quelima/iMars SQ11 camera, only 9 grams here at Banggood https://www.banggood.com/Original-Mini-Camera-SQ11-HD-Camcorder-HD-Night-Vision-1080P-Sports-Mini-DV-Video-Recorder-p-1139282.html?p=XE271782188502016122
thingiverse
SQ11 cam mount for flat or curved surfaces like an RC vehicle or a motorcycle helmet. This was modified from another SQ11 mount on here. ... Slip the cam in from the top and tape, glue or fasten mount to whatever.
thingiverse
I added an empty area in the front in order not to block the FPV camera under. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/kLzEDrE1A5u
thingiverse
Camera mount for the Original iMars™ Mini Camera SQ11 camera. Tilted 30 degrees. ... USB-connector is exposed but memory card is protected by the case.
thingiverse
# SQ11 Camera holder. - Camera fits perfect. - Inclination (<45º) and rotation supported. ... __ Important__: need to be plugged on a base (8mm diameter hole) ## Instructions - Print it - Put the slider inside the camera holder slider's slot - Plug...
thingiverse
added a holder for the very cheap SQ11 HD camera to my existing battery mount. Note, the FOV of the SQ11 is pretty bad. There are youtube videos about how to swap out the lens like I have. I've used PLA and the holder arms are very brittle,...
thingiverse
A very simple remix of the SQ11 clip provided by christosch to enable the SQ11 camera to be taped down - in my instance the wing of my Mini Talon RC plane.
thingiverse
This is a BT60 SQ11 Camera Spacecraft for Estes 41mm Diameter Rocketry Tubes.
thingiverse
The angle of the original "SQ11 HD camera mount for Lumenier QAV R quadcopter" was way too low. ...So I've modified it to match to FPV camera angle, and made couple cuts for ease of mounting and inserting camera.
thingiverse
I also replaced the metal support around the SQ11 camera with this: https://www.thingiverse.com/make:396316 from https://www.thingiverse.com/thing:2533945. Weight of the modified camera with memory card is 10.56g. Weight with the camera, memory...
thingiverse
Simple print to let you use an SQ11 camera as an FPV or RunCam workalike with versatile mounting slots to attach to the top deck of a FPV Quadcopter.
thingiverse
on Facebook](https://www.facebook.com/makebreakrepeat/): Updates on Tuesdays and Thursdays!* [Quelima SQ11](https://amzn.to/2FfN0PB) action camera mount compatible with most action camera mount systems. Clips onto the camera back and allows for 180º...
thingiverse
There are holes in the one side to lock the camera in place. I just use a piece of twist tie from a bread bag because it's easy to remove. You could use a paper clip too I guess. I have included the Tello mount, but also a STEP file of the same...
thingiverse
This is SQ10 stock holder replacement. I've made it, because default holder has poor quality and it's not so good for car. This one is designed for Focus MK1 dashboard, but I also made universal mount part for it (holder02). I printed it with ABS -...
cults3d
This is SQ10 stock holder replacement. I've made it, because default holder has poor quality and it's not so good for car. This one is designed for Focus MK1 dashboard, but I also made universal mount part for it (holder02). ...I printed it with ABS -...
thingiverse
SQ11 Minicam Camera mount for X-UAV Sky Surfer X8
thingiverse
Arrowhead made for carbon or aluminum arrows, suitable for SQ11 Mini DV camera. ... A standard arrowhead was glued into the hole of the head so that it could be threaded to the arrowhead.
prusaprinters
SQ11 Minicam Camera mount for X-UAV Sky Surfer X8 Print Settings Printer Brand: Prusa Printer: Prusa Mk2 Rafts: No Supports: Yes Resolution: 200 Infill: 20 Filament: PolyMaker PLA Category: Hobby
thingiverse
I was asked to make a mount for this camera (SQ11 HD) by a friend He needed to mount it on his quad a Lumenier QAV-R The hole centres in the mount are at 30mm so should fit quiet a few quads
thingiverse
SQ11 Camera mount meant to be used with velcro straps. ...I put a hole on the bottom to easily remove the camera with a pen.
thingiverse
I mixed together a larger camera car, with a holder for the smaller SQ11 camera, and did some trimming to allow it to print faster / be shorter and keep it from overhanging too much in curves. The pic shows temp old trucks with Rapidos... I...