squirrel salt and pepper shakers 3d models
2290317 3d models found related to squirrel salt and pepper shakers.cults3d
A cute salt and pepper shaker that is shaped like a squirrel. The salt is poured into the bottom by unscrewing the cap. ...The eyes of the squirrel are the outlets Enjoy!
thingiverse
A cute salt and pepper shaker that is shaped like a squirrel. The salt is poured into the bottom by unscrewing the cap. The eyes of the squirrel are the outlets Enjoy! Print Settings Printer: Up Plus and Up Box+ Rafts: Yes Supports: Yes Resolution:...
cgtrader
A cute salt and pepper shaker that is shaped like a squirrel. The salt is poured into the bottom by unscrewing the cap. The eyes of the squirrel are the outlets How to print: 0.2mm Layer Height 80% Infill Print with minimal or no support settings so...
thingiverse
This stand covers the squirrel's eyes and gives it a secure stand for filling it up. I used TPU filament for a snug fit without putting stress on the squirrel's ears. To subtract the squirrel from the base block in Tinkercad I used the squirrel STL...
thingiverse
This little funnel makes filling the squirrels (thing 138777) very easy and keeps the thread for the closure cap clean. ... The filling stand is here: https://www.thingiverse.com/thing:3560611
thingiverse
Salt and Pepper shakers Print Settings Rafts: Doesn't Matter Supports: No Resolution: .02 Infill: 100%
cults3d
The wife kept getting mad at me for leaving the salt and pepper shakers in my printing room, so I made these to keep in here. ...printed at .2mm layer height no bed adhesion and no supports.
cults3d
The wife kept getting mad at me for leaving the salt and pepper shakers in my printing room, so I made these to keep in here. ...printed at .2mm layer height no bed adhesion and no supports.
thingiverse
This is a salt and pepper shaker I designed while working on a sugar dispenser for my favorite brother-in-law. It is about 8 cm tall. The lids are held in by friction. The salt shaker has 6 holes, the pepper has 8. It is very flexible and easy to...
sketchfab
Salt and pepper are typically maintained in separate shakers on the table, but may be mixed in the kitchen. Some food writers, like Sara Dickerman, have argued that in modern cookery, a new spice could be used in place of black pepper. Info Link:...
cults3d
... naughty's, kind of funny so I think I will keep it. ...The wife kept getting mad at me for leaving the salt and pepper shakers in my printing room, so I made these to keep in here. ...printed at .2mm layer height no bed adhesion and no supports.
cults3d
The model contains the most popular formats: .obj; .stl; Each file was checked for opening and full content by the model. Thank you for coming to see this model. ...Also pay attention to other models by clicking on the name of the account in the right...
thingiverse
Salt and pepper shakers. ... Use the customiser to customise your customised tips to salt and pepper shaker. Bigger holes for more salt and pepper on food / deal with over extrusion. Enjoy. ps. ...Print without supports
thingiverse
Enjoy these salt and pepper shakers! Word reveal on the bottom The top screws in place. ...No supports needed.
cults3d
Enjoy these salt and pepper shakers! Word reveal on the bottom The top screws in place. ...No supports needed.
myminifactory
Fun Salt and Pepper Shakers! Designed in Fusion, the lid screws into place. No supports necessary for print. ...Enjoy, for more prints check out @drfempop on instagram.
cults3d
Salt and Pepper Shakers, yay! Easy print, no supports needed. The lid screws into place. ...The peppered look of the PLA is using a 'marble' PLA if you are curious.
thingiverse
Salt and pepper shakers set. For salt, black and red pepper. Avg. shaker size 77 x 40 x 40 mm (3 x 1.6 x 1.6 in). Can be printed without supports (except stand handle). ...Maximum layer height is 0.2 mm.
thingiverse
It's almost a no-brainer that the salt shaker be printed in white and the pepper in black. But we're more imaginative than that. And who says the top and bottom need to be the same color. Shake it up and have fun with it. Each shaker consumes about...
thingiverse
elsa salt and pepper shaker the bottom screw screws into the threaded area at the bottom of elsas skirt. . this is where you put the salt or pepper. make 2. 1 for salt and 1 for pepper. in colors of your liking. it uses a 3 mm (appx) hex wrench...
myminifactory
Upcycle your old lightbulbs into these awesome Salt and Pepper shakers! Really quick and easy to print out, the heads fit any standard screw-top lightbulb. Salt and Pepper not provided, the stand is printable as a separate object from my profile,...
cults3d
These are 9mm bullet salt and pepper shakers. I modeled this from a real bullet. Super simple I recommend printing the bottom with either a bronze or gold and the top with a copper pla. Recommend working the threads in till any blobs or expansion is...
thingiverse
Print both Darth Vader top and the storm trooper at ZERO Percent INFIL. I had to do it this way to make it work. Darth Vader is 2 parts. After printing the head @ ZERO % infill ,the bottom has to be opened before gluing the base to it. Print 2...
youmagine
... After I made sure everything was placed correctly and connected, I exported it as an STL and uploaded it into Meshlab. In Meshlab I flattened all the layers and then repaired any errors left in the file. Then I sliced them in Cura and printed them.