ssd hdd adapter 3d models

2,5" to 3,5" SSD/HDD adapter

This is a 2.5" SSD/laptop HDD adapter. Its purpose is to fit a 2.5" HDD/SSD into a 3.25" hot swap bay. This adapter is providing the shape and connections of a 3.25" HDD to any 3.25" slot including screw holes (where possible). Therefor you can use...

I had no space in my NAS for more 3.5" HDDs, but spacy wall mount for 2.5" HDD/SDD. ...So, with this adapter i mounted 4xHDD discs on a 2.5" disc mounting place. ... Print with good infill like 42% and ABS or ASA against deformation.

...Screws holes are still on the underside in case you use this with a laptop HDD. ... Edit: Shortened it by 3mm because the extra height was solely a byproduct starting with a nice round number at 10mm extrusion, and didn't seem to offer any benefit.

... uses a hexagonal pattern with a 3mm border to more evenly distribute flexing while minimizing material usage. It has same previous holes and I added the underside screw holes to match an HDD.Print SettingsPrinter: CR10S PROSupports: No

There are pins to allow you to snap-in an SSD without needing screws, but there are also 4 screw holes underneath for mounting a standard laptop HDD as well.The SATA connector itself will be offset approx. 3mm due to the necessary railing thickness,...

I buy a new SSD for my PC, and the case bay was prepared only for 3,5" HDD.

Based off http://www.thingiverse.com/thing:168750 by Clax, after I made one I realised I needed the other two mounting holes on a 3.5 HDD to fit my drive bays in my Antec P182 case. ... This is the result!

... extra holes to acomodate for Floppy drive bay installation. ...-original only supports 3.5 HDD bay. Side walls now have full enforcement, via 45 degree bracket. -much stronger and better longevity. ... Recommended for use with fine-thread screws.

Adapter to hold 2x 2.5" drives in a single 3.5" bay. ...Remixed from [Tadziurski's](https://www.thingiverse.com/tadziurski/designs), original design [here](https://www.thingiverse.com/thing:1942247). solid state hard drive adapter

Tried to created an all in one 2.5" to 3.5" adapter bracket that does not require extra screws to hold smaller drive in place. ... Any helpful comments are welcome.

UPDATE: V4 has repaired support interface. This part is notably difficult to print. I will update it as I find issues. Only use support with the single side model!!! I designed this for a clients server. This part is designed to house two 2.5" drives...

Added screw holes to mount HDD or SSD firmly. ... [2021-05-17 EDIT] Added remix (AA8_ssd 95.stl) for 9.5mm HDD/SSD. ...Original file (AA8_ssd.stl) is for drives up to 7mm.

Planning to setup mirrored 2.5" SSD drives in a new media server and needed an adapter to mount them in one 3.5" HDD slot/bay. ... <a rel="nofollow ugc" href="https://ko-fi.com/john_u"><img src="https://i.imgur.com/KjJjavu.jpeg" alt="Buy Me a Coffee at...

To reduce the plastic left only a corner

A simple adapter to fit a 2.5 inch SSD or laptop HDD to a PC case with mounts only for 3.5 inch hard drives.Sadly do not have a photo of this one, since it was specially made for a customer and then never seen again. So here are some OpenSCAD...

This SSD adapter was 3D printed to accommodate a standard sized SSD drive and give it the exact footprint of a full size HDD. This can be used for all hot-swap bays usually found on a server type chassis, as it will fit the form factor of a normal...

Adaptor for PS2 FAT SSD Tested on Samsung Evoline (860 QVO) SSD dimensions LxWxH 100mm 70mm 6mm PS FAT HDD-Space dimensions LxWxH 151mm x 106mm x 27mm Adaptor dimensions LxWxH 150,4mm x 105,34mm x 26,5mm Misc Enjoy

This SSD adapter was 3D printed to accommodate a standard sized SSD drive and give it the exact footprint of a full size HDD. This can be used for all hot-swap bays usually found on a server type chassis, as it will fit the form factor of a normal...

I had to replace my old hard drive (3,5" HDD) in my iMac so i decided to put in an SSD instead of a new HDD. It's the 2015 version (EMC 2834), but this bracket schould fit in any iMac. For the Replacement I followed the instructions of ifixit. You'll...

Adapter to install two HDD/SSD on one 2.5" mount in your PC.

This is the adapter to fit SSD inside the iMac 24 from early 2009. I used PETG, because of temperatures inside enclosure. ... PH1 M3x16mm bolts are used to fit the SSD.

Kobol adapter was out of stock so I decided to design and 3D print an alternative, based on their design. I used M3 5mm threaded inserts for screwing it to the pink caddy, and the 2.5" HDD uses four M3 screws. If you have no threaded inserts you...

Was rebuilding/expanding my server and needed 2 extra HDD slots.None of the designs I saw were really what I wanted, so I designed this to mount HDDs in an optical drive slot. The screw hole spacing matches the standard spacing on the drives I had on...

Screwless adapter for 2 2,5" HDDs or SSDs in one 3,5" port

... laying around, feel free to customize it. Please note the adapter has top/down orientation. Top screw holes are 4mm away from the edge where the bottom holes are 3mm away from the edge. ...This is done to fit those modern 7mm thickness drives.

This remix is adapted to reduce the amount printed material. ... Original design: https://www.thingiverse.com/thing:1706655

This remix is adapted to reduce the amount printed material. ... Original design: https://www.thingiverse.com/thing:1706655

This is a triple SSD to 3.5" HDD Adapter. Attention! The height is more than one standart Slot! The SSD´s have enough Space to get them cooled with ahFan from behind and the Power and Data Cables fit. ... UPDATE: Double SSD Adapter in Downloads ;)...