ssd to hdd adapter 3d models
2101048 3d models found related to ssd to hdd adapter.thingiverse
Tried to make a snap in design, minimize filament usage, and keep port/hole positioning as close to OEM as possible. The SATA ports themselves will be 3-4mm farther inward than OEM making it incompatible with slide in docks/mounts, but it's...
prusaprinters
Designed a new SSD bracket from scratch.Tried to make a snap in design, minimize filament usage, and keep port/hole positioning as close to OEM as possible.The SATA ports themselves will be 3-4mm farther inward than OEM making it incompatible with...
prusaprinters
There are pins to allow you to snap-in an SSD without needing screws, but there are also 4 screw holes underneath for mounting a standard laptop HDD as well.The SATA connector itself will be offset approx. 3mm due to the necessary railing thickness,...
thingiverse
I had no space in my NAS for more 3.5" HDDs, but spacy wall mount for 2.5" HDD/SDD. ...So, with this adapter i mounted 4xHDD discs on a 2.5" disc mounting place. ... Print with good infill like 42% and ABS or ASA against deformation.
thingiverse
This SSD adapter was 3D printed to accommodate a standard sized SSD drive and give it the exact footprint of a full size HDD. This can be used for all hot-swap bays usually found on a server type chassis, as it will fit the form factor of a normal...
prusaprinters
This SSD adapter was 3D printed to accommodate a standard sized SSD drive and give it the exact footprint of a full size HDD. This can be used for all hot-swap bays usually found on a server type chassis, as it will fit the form factor of a normal...
thingiverse
I used this to mount 2 SSDs on one HDD tray. The overall height from the very top of the top drive to the bottom of the bottom drive is 1 inch, which is the thickness of a 3.5 in. HDD. I uploaded Sketchup file, so you can customize the thickness as...
thingiverse
This remix is adapted to reduce the amount printed material. ... Original design: https://www.thingiverse.com/thing:1706655
cults3d
This remix is adapted to reduce the amount printed material. ... Original design: https://www.thingiverse.com/thing:1706655
thingiverse
This is a triple SSD to 3.5" HDD Adapter. Attention! The height is more than one standart Slot! The SSD´s have enough Space to get them cooled with ahFan from behind and the Power and Data Cables fit. ... UPDATE: Double SSD Adapter in Downloads ;)...
thingiverse
Mounts a standard SSD into anything that takes a standard 3.5inch HDD. Mounting holes for SSD and mounting holes for HDD. ...Made to fit into the stock Dell hard drive tray.
thingiverse
Here is a 2.5" SSD to HDD Spacer adapter. It basically makes a 2.5" SSD into the size of a 2.5" HDD (thicker). You might need it if you install an SSD into some external hard drive cases. Use double sided tape to stick it to the SSD. This object...
thingiverse
I had to replace my old hard drive (3,5" HDD) in my iMac so i decided to put in an SSD instead of a new HDD. It's the 2015 version (EMC 2834), but this bracket schould fit in any iMac. For the Replacement I followed the instructions of ifixit. You'll...
prusaprinters
The screw hole spacing matches the standard spacing on the drives I had on hand.I figured I should add the SSD bottom screw holes to allow it to mount either.Depending on your cases screw holes, you might be able to stack 2 of these in 1 slot, but I...
thingiverse
This is a drive adapter from 3.5 to 2.5. allowing you to mount a 2.5 inch drive in a 3.5 inch drive bay. ...this was designed to work with the tool less bays but will work with either
thingiverse
This is an adaptatio of Mootzerely design: https://www.thingiverse.com/thing:5256622. ... SSD Samsung 870 EVO adapter for DELL tray.
cults3d
I had useless mSATA SSD. ...Bought an adapter on ebay for it http://www.ebay.com/itm/201336720279 This thing is an adapter for 2.5 inch HDD size. ...So basically is adapter for adapter :)
thingiverse
... ...Bought an adapter on ebay for it http://www.ebay.com/itm/201336720279 This thing is an adapter for 2.5 inch HDD size. ...So basically is adapter for adapter :) Print Settings Printer: Ord bot Hadron Rafts: No Supports: No Resolution: .25 Infill: 50%
thingiverse
Print Settings Printer: Scalar Custom Rafts: Doesn't Matter Supports: No Resolution: 0.2mm or numerically lower Infill: 10%+ Notes: Again, this will be a fairly tight fitting part, designed to be printed with rigid material (PLA, ABS). Supports are...
prusaprinters
Remix to accept a 9mm drive. Category: Computer
thingiverse
This model is an adapter for a Dell OptiPlex 3060 HDD tray for an SSD. The mounting holes are derived from a Samsung 870 QVO and a Western Digital HDD. It took three revisions before the final design, hence the "v3" in the STL file name. I...
thingiverse
Planning to setup mirrored 2.5" SSD drives in a new media server and needed an adapter to mount them in one 3.5" HDD slot/bay. ... <a rel="nofollow ugc" href="https://ko-fi.com/john_u"><img src="https://i.imgur.com/KjJjavu.jpeg" alt="Buy Me a Coffee at...
thingiverse
I adapted (pun intended) this model to reduce plastic requirements and improve airflow, as SSD don't move anyway. Pick your poison: I'm bestowing you with 3 variants to feel the thrill of overloading your case with more-than-intended storage. ...Keep...
thingiverse
Differences from original: Added extra holes to acomodate for Floppy drive bay installation. -original only supports 3.5 HDD bay. Side walls now have full enforcement, via 45 degree bracket. -much stronger and better longevity. ... Recommended for...
thingiverse
Based off http://www.thingiverse.com/thing:168750 by Clax, after I made one I realised I needed the other two mounting holes on a 3.5 HDD to fit my drive bays in my Antec P182 case. ... This is the result!
thingiverse
Adapter to hold 2x 2.5" drives in a single 3.5" bay. Remixed from [Tadziurski's](https://www.thingiverse.com/tadziurski/designs), original design [here](https://www.thingiverse.com/thing:1942247). ... solid state hard drive adapter
thingiverse
Tried to created an all in one 2.5" to 3.5" adapter bracket that does not require extra screws to hold smaller drive in place. ... Any helpful comments are welcome.
prusaprinters
It has fit all standard optical bays we have tested it in and allows you to fit an extra 2.5" from the bottom or 3.5" drive from the sides.If you find any problems with the model, please let us know and we will attempt to fix them within...