stackable dvd rack 3d models

Stackable Spice rack

A simple stackable rack for 36 Copic® markers.

A simple stackable rack  for 36 Copic® markers.

A Stackable Sleek Can Rack.It is modular, have fun =)

Stackable Rack module to organize small electronic devices.

Commercial variations were too expensive, this lightweight CD rack is stackable and can be used either in  a vertical or horizontal orientation.

My first Thing uploaded to Thingyverse! ...It's just an easily expandable/stackable CD Rack. ...Print one for each CD you got and have a nice shelf.

This is a stackable test tube rack that can hold 77 test tubes. Please note that this model is for personal use! ...Selling this model is prohibited.

stackable jumper wire rack to hold all your wires. (file included is made for 20cm cables. ...If you need it longer or shorter just change the length of the connectors.)

a stackable rack for deluxe sized car transformers this is a remodel of https://www.thingiverse.com/thing:4253620/files i tried to put it up as a remix but it would not work

A simple stackable rack for 36 Copic® markers. Print instructionsIt's a "big" print and the bottom part should be really flat (in order to be stackable). ...So, be sure to have good bed adhesion to avoid any warping.</p>

... in the scad-file). If you prefer a design that prints faster and needs less filament, take a look at our Stackable Rack (light version). ... Since stl-files are created with OpenSCAD, they often need to be fixed with Netfabb before printing.

A modular, and stackable rack for 4 full size HDD and two rack for SSDs. This is compatible with a single 120mm fan for air flow. Perfect for any open air case or a NAS server! Comment any improvements you'd like to see Includes 4 versions with...

A stackable can rack that is easy to print and assemble. I would suggest adding some rubber, or something grippy, to the area that touches the can. The racks tend to slide around a bit. Update! I added strips of rubber to the rack and, as...

We use it for sample vials (dimensions for 1.5 mL and 4 mL are stated in the scad-file). If you prefer a design that prints faster and needs less filament, take a look at our Stackable Rack (light version). Since stl-files are created with OpenSCAD,...

The rack can be stacked for a low footprint storage solution.20mm wooden dowel used for the spool storage rack.&nbsp;Update: 12.01.22New version added with 22mm holes.&nbsp;Update: 30.03.22New version added with 30mm holes. ...Warning: It is unknown if...

This design requires much less filament and printing time than its predecessor, Stackable Rack (solid version). Rendering in OpenSCAD takes some time at the preset resolution (0.05). Also, the stl-files usually need to be fixed with Netfabb...

This stackable soap rack allows you to leave one bar of soap to dry while using the other. Printable with minimal support! Note 2020/03/20: It should work, but it's not tested yet, so I will print and update if necessary. Print instructionsFor the...

------------------------------------ Modular stackable shoe rack. low floor ---- support platform high floor ----- stackable upper floors Pillars -------- Support two floors - 150 or 200 mm Cap -------------- Cap for the last floor. Possible...

support of 5 citadel paint infinitely stackable.

a stackable tray for storing sodimm ram

A remix of the modular stackable shoe rack with a few changes from the original: * Slightly smaller - 215mm wide, so it will fit on my Ender 3 bed * Hole size adjustment - I had a hard time finding 15mm rods, so I resized the holes for 5/8" wooden...

Hey folks, Since I couldn´t find any test tube holders/racks which were stackable and suited me for antkeeping founding chambers I used the spare time to design it myself in fusion 360. Very simple design but does the trick. Might also be usuable for...

Check out the spool holder I designed as an add-on feature: "Spool Holder for the Stackable Freestanding Filament Rack" (https://www.thingiverse.com/thing:2953103). ... I extended the top bars over my printer and added a spool holder to get the weight...

We use it for sample vials (dimensions for 1.5 mL and 4 mL are stated in the scad-file). This design requires much less filament and printing time than its predecessor, Stackable Rack (solid version). Rendering in OpenSCAD takes some time at the...

A stackable can rack that is easy to print and assemble. Print two crossbars and two rack bodies. I would suggest adding some rubber, or something grippy, to the area that touches the can. The racks tend to slide around a bit. Update! I added strips...

A simple stackable rack for 36 Copic® markers. Print Settings Printer Brand: Prusa Printer: i3 MK3Rafts: No Supports: NoResolution: 0.2 Infill: 5% - 10% Filament: Fillamentum PLA, PETG Category: Art Tools

This is a stackable spice rack that can also be adapted for other applications.&nbsp;I have used a couple wood screws to attach the handle to the shelf. The racks also feature a location to secure a 4mm x 2mm Magnet.&nbsp;The tolerance for the...

Stack-able spice racks/storage. ... Included the Fusion 360 project.

To keep them at the right place and for easy availability, I designed this stackable, parametric Rack. I let the needles stay on the syringes when I store them, but you can also remove the needles for safety reasons, just make sure you change the...