stampede rc truck 2wd 3d models
48840 3d models found related to stampede rc truck 2wd.thingiverse
I drive my Stampede with a bigger battery, so I hab to lift the ground-plate (wit esc and receiver) a little bit and needed a new holder for my battery (Absima 3s 4000mah hardcase).
thingiverse
Simple replacement bar for the 2wd stampede. I printed in TPU and it's indestructible. Recommended to print in ABS or best is TPU or Polycarbonate .2 resolution 100% infill. ...Higher temps and slower speeds for best strength
thingiverse
These are front and rear airless tires for a Traxxas Stampede. I have not had a chance to print and test these. They are designed to be printed at a low infill (<25%) with TPU (or any flexible) material. ... Please drop a comment if you try them out!
thingiverse
https://www.youtube.com/watch?v=PISuP-I2B_M Besides hardware, here are the off-the-shelf components you'll need: Traxxas Bandit/Rustler/Slash (2WD) transmission assembly and drive shafts (front and rear) 12mm hubs and wheels/tires Shocks 110-ish for...
prusaprinters
I will also be doing CAD live streams to help whomever stops by). Besides hardware, here are the off-the-shelf components you'll need: Traxxas Bandit/Rustler/Slash (2WD) transmission assembly and drive shafts (front and rear) 12mm hubs and...
thingiverse
This lipo battery holder was made to help me add a big 2S 5500mah battery to my RC Traxxas Rustler. To use it you must remove the plastic piece in the rear of the Rustler that would normally support the ESC and relocate the ESC with double side...
thingiverse
Needed Front Mount 2 x M4x30 1 x M4x10 Rear Mount Using a standard hex screw will slightly enlarge the rear holes,It would better if you can find a longer stock screw. 2 x M3x20 2 x M3x10 Used the following LED Kit. ... ...
thingiverse
This lipo battery holder was made to help me add a big 2S 5500mah battery to my RC Traxxas Slash. Instead of the battery going into the hole made for it, you place the print into the area and use the clip to hold it on. The balance lead hides out in...
thingiverse
Designed for a 2wd Slash (pictured), but will also fit the 2wd Stampede, Rustler, and Bandit. Fan angle is 30 degrees. You'll need 2 or 4 3x15mm (Traxxas #2579) or 3x16mm button head screws and M3 nylock nuts to secure the fan to the mount. ...Using...
cgtrader
**Mounting it to the RC Car: **See the above pictures in order starting where it says Mounting Instructions (Demonstrated with the left ski). All what you need to do now is mount them to the RC car and you're done! These simply mount on the RC car...
thingiverse
The mount is only meant for a Stampede bumper and it attaches with three bolts that go through the 3 holes in the bumper and the mount with 1/4 inch holes. I haven't tested it out yet since the prototype I have at the moment is made out of just...
thingiverse
Needed a way to hang my RC cars on the wall, so I made this on to fit my Traxxas Son-uva Digger 2WD Monster Truck. The hanger fits all Stampede 2WD based models e.g. ...Bigfoot, Gravedigger, Monster Mud etc.
sketchfab
Kyosho Raider 2wd 1988 vintage buggy rc car. ...Restored and upgraded Canopy and some internal parts redesigned with 3D Fusion and printed with Ultimaker 2e
thingiverse
Convert your Tamiya Mini 4WD VZ Chassis with our 3d printable parts, some screws and RC electronics to a full proportional 2WD radio controlled car. ... Check out the build guide at: https://airc-pirates.com/mini-4wd-vz-chassis/ VS Chassis parts...
cgtrader
3D model of a 2 wheel drive pickup truck chassis. The chassis high detail exterior is great for close up renders. Handlers have been added so you can manipulate it for poses. The model was created with 3DS Max 2016 using the open subdivision...
thingiverse
Convert your Tamiya Mini 4WD VS Chassis with our 3d printable parts, some screws and RC electronics to a full proportional 2WD radio controlled car. You will find more information in the build guide of the VZ Chassis. Currently there is only one...
cgstudio
3D model of a 2 wheel drive pickup truck chassis.The chassis high detail exterior is great for close up renders. Handlers have been added so you can manipulate it for poses.The model was created with 3DS Max 2016 using the open subdivision modifier...
cgtrader
3D model of a 2 wheel drive dually pickup truck chassis. The chassis high detail exterior is great for close up renders. Handlers have been added so you can manipulate it for poses. The model was created with 3DS Max 2016 using the open subdivision...
thingiverse
Needed a way to store my rc cars so I made this wall holder/hanger/hook to hang them on the wall. ...It fits all Traxxas 2WD Stampede-based monster trucks such Bigfoot, Gravedigger, Monster Mud, Grinder, Son Uva Digger etc.
thingiverse
Due to a the installation of a new RC motor and ESC, I felt the need to switch the ESC position with the ESC position. So I created a plate to mount te receiver with screw holes for the Hobbywing EZrun Max10SCT. Soif you have that one, you can screw...
thingiverse
Update 5/12/2015 Did some bashing with the Stampede and surprisingly it has held up! Even after a few bumps! I repaired the .stl and fixed some of the geometry problems with the original. ...Now every lines up better and when the suspensions at full...
thingiverse
READ THIS, I MEAN IT. Experience was gained and lessons learned..... From El Cheapo labs I have made this tube reinforcement for my low budget Slash Drag car. This will also fit other Traxxas models using the same axle. This is one of many economy...
cults3d
I wanted to secure my battery wires so i designed this new battery hold down that holds and guides the wires back towards the ESC. Keeps the wires close to the battery and out of harms way. Prints easily but does need supports (at the arch) and i...
cults3d
Diecast Tesla Cybertruck pulling truck 2wd Scale 1 to 25
thingiverse
Customized version of https://www.thingiverse.com/thing:127588 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=127588
thingiverse
My son needed a place to put his R/C trucks so I threw together something real quick in Tinkercad and this is the result. It's not perfect but it works for what I needed, and my son is happy to have a way to store and display his R/C trucks. The...