stand for blue snowball 3d models
2295137 3d models found related to stand for blue snowball.thingiverse
An ultra low profile stand for the Blue Snowball stand. 5/8-27 mount for the mic. Just enough clearance to fully tilt the microphone on the screw. 70mm diameter base ensures the microphone won't tip or roll while still being a small footprint...
thingiverse
Use this part to mount Blue Snowball to your table lamp stand.
thingiverse
My improvement, is that the shockmount can be used on the original Blue Snowball microphone stand. One M3 screw is needed for mounting the outer ring to the threaded part. And of course, some rubber bands or hair ties to mount the microphone. The...
thingiverse
ad895 had made the design for the original nice all metal Snowball stand. I wasn't as lucky when I bought mine, and got the other cheap, partly plastic, stand. The mount needed some changes as the stands have different diameters. The downscaled...
thingiverse
Remix of clypp's design (https://www.thingiverse.com/thing:4315674) Used for the Blue Snowball iCE microphone, particularly for the models where you can't screw off the stand. This revision makes it so the parts wrap around the stand. Previously, you...
thingiverse
a shorter stand for the blue snowball microphone, or softballs i'm not your mother.
thingiverse
Looking for a more compact stand for your Blue Snowball? You've found it! This stand lowers the height of the microphone by 4.5" (115mm). Rubber non-slip feet allow for a stable platform. This stand does require these rubber bumpers. 10mm x 4mm...
myminifactory
I wanted to practice making 3d printed threads, and I wanted a new microphone stand. So here is my collection of dead simple stands for the Blue Snowball microphone. There is a super short one that might be usefull for gaming or putting on a shelf....
thingiverse
Microphone stand for Yeti blue snowball mic. ...I wanted to make it shorter, but the USB cable angles down, so this gives the cable enough clearance, while still lowering the mic under my monitor.
myminifactory
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. V4 sits lower. ... Fusion 360 archive...
thingiverse
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball. I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. I used dynamic layer height in...
thingiverse
I designed this, because the normal max hight is not enough for me. ... I printed this with 20% infill, no raft and no support.
thingiverse
A low profile 20mm tall stable stand for the Blue Snowball mic as others I had seen and tried didn't provide the stability I'd like (I'm pretty clumsy). I have used rubber foam pads on the base to reduce noise, this worked very well. ... The mic...
thingiverse
I created a fairly simple shock absorber for my Blue Snowball. You will need: 2 x inner ring pieces 2 x outer ring pieces superglue 8+ hair bobbles Thread the bobbles through each loop and hook onto neighbouring pins. The microphone should...
thingiverse
This is a short desk stand for the Blue Snowball microphone. I designed this to be able to fit the mic below my monitors. The existing designs I found didn't have any space between the base plate and the mic meaning it wasn't possible to tilt the...
thingiverse
The assembly for holding the legs of my microphone to the stand craked around the hole for the screw, probably due to overtightening. This lead to the lower part of the microphone stand becoming loose, and it would spin whenever I picked up the...
thingiverse
Mic/camera stand for over your monitor/tv, adjust it for your model. ... This exact is for the Blue snowball mic. ... Use PLA with infill at 10-20%
prusaprinters
A tall, simple, stand for microphones that use 5/8"-27 UNS threads, like the Blue Snowball.I thought the stock stand was too low, and I wanted a stand where the mic was close in front of my mouth, not below me. ...The stand is slim, but sturdy and sits...
thingiverse
The regular Blue Snowball shock mount was huge, which made it awkward to use if you need to see past it, so I designed this tiny one that uses rubber bands for dampening. You'll need the small pipe that attaches to the microphone from the desk stand...
thingiverse
I tried printing ad895's (https://www.thingiverse.com/thing:2225557) version but for the version of Blue Snowball I have the mount is too short and the hole is way to wide. When that didn't work I tried GuruX's version...
thingiverse
A small bracket for adapting the blue snowball onto the end of a swing arm lamp. Similar to This one on amazon. The Peg is slightly oversized, to allow the microphone to cut its own threads. A small bump is included on one side to help with rotation....
thingiverse
Needed a small form factor pop filter for my snowball mic and i didn't feel like spending 20$ on a few cents worth of plastic, print 2 of the mesh holders, glue a piece of thin fabric/mesh between them before gluing them into the model itself. ... 2...
prusaprinters
Pop filter which connects to a Blue Microphone.Add a couple layers of thin fabric will do a decent job of blocking your puffs of air.One of the securing rings has space for a 6mm inner diameter spring to help press it against the outer ring.Mounting...
thingiverse
This is a replacement part for the Blue Snowball mic stand. The legs have a lot of pressure on the factory plastic part and is prone to breaking. Simply print with about 35 - 40% infill, no supports are needed. ... V4 sits a bit lower Fusion...
thingiverse
Simple stand to replace my blue snowball mount (non-adjustable) after I accidentally dropped and broke the original one
thingiverse
I made this simple adapter to be able to attacth my Blue Snowball to my smartphone tripod.