stand for kindle fire 3d models
2353408 3d models found related to stand for kindle fire.thingiverse
... is the same two tablet stand pieces as the original, with a brace in the middle to join them as one solid unit. ...Tablet in the picture is a Kindle Fire 8 inch. It fits both horizontally and vertically. ...Similarly sized tablets should work as well.
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=46887 Instructions Using the following options: pattern_size = 35 stand_width = 10 number_of_lids = 1 pattern_offset_y = 0 pattern_offset_x = 0 slot_depth = 10.0 extra_length_percent = 0...
thingiverse
This is a 3D printable stand for the Kindle Fire. It is a derivative of http://www.thingiverse.com/thing:4020 by eagleapex. The Kindle Fire is a little thicker than the iPad so I widened the gap where the tablet sits. This also works for the Xoom...
thingiverse
Customized version of https://www.thingiverse.com/thing:2835028 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2835028
thingiverse
... this model yet, but I am about to. ...I designed it on F360 to work with my mothers kindle fire. It should work with a case and an over all thickness up to 2.6cm. ...Its 11cm long and should be optimal for tablets in landscape mode or portrait.
thingiverse
Tablet Stand I designed using the new $50 Kindle Fire Tablet(with no case of any kind). There is cable management built into this stand. I print using a M3d printer. ... Print Settings Rafts: No ...
thingiverse
Dual-angle and single-angle stand for Kindle Fire HD tablet (9.9mm thickness). ...
thingiverse
Stand for Kindle Fire Tablet Gen. 6 Upright One nut and M6 bolt is needed ---------------------------------------------------------- Ständer für Kindle Fire Tablet Gen. ...6 Hochkant Es wird eine Mutter sowie Schraube M6 benötigt
thingiverse
Minimal Stand for Kindle Fire 6 - Great for Airplane (Tab on back is to be removed - it makes removing from printer easier)
thingiverse
A basic stand for my Kindle Fire HD8 to use while using video apps. It fits into the slots pretty closely without noticeable bending of the tabs. ... Cura said it would use 47g of filament though I weighed the final product at 34g.
thingiverse
I made this stand for my Kindle Fire. It would probably hold other tablets quite nicely but I've only tested it with the Fire. Works horizontally and vertically. Instructions Print two of each part...
pinshape
its a stand for a kindle fire 8" kids edition. I'm not sure I would buy this tablet again.. but as Santa brought it already, I designed this stand so my daughter doesn't need to hold it while watching it. If you print it, don't forget to add...
prusaprinters
its a stand for a kindle fire 8" kids edition. I'm not sure I would buy this tablet again.. but as Santa brought it already, I designed this stand so my daughter doesn't need to hold it while watching it. If you print it, don't forget to add you...
thingiverse
its a stand for a kindle fire 8" kids edition. I'm not sure I would buy this tablet again.. but as Santa brought it already, I designed this stand so my daughter doesn't need to hold it while watching it. If you print it, don't forget to add...
thingiverse
Minimalist stand for Kindle fire 7", 7th generation. It will either snap or slide over the body. The stand folds down flat, so it's easy to slide under a pillow. The kick-stand is connected to the holder body via friction.There's little nubs that...
thingiverse
*** I have also re-designed this mount to use less parts and also be a bit stronger in the pivots: https://www.thingiverse.com/thing:3309954 *** Here's my take at a collapsible stand for the Kindle Fire 7 with the rubber bumper cover. I may have made...
thingiverse
This is a stand for the Kindle Fire an it will also cradle an iPhone, iPad or any smart phone. Instructions Just print this using your favorite 3d printer. ...Enjoy!
thingiverse
Small Kindle fire stand to mount an Octoprint interface. Printed at 0.2 layer height. 20% infill. Drill directly into a wooden surface. Print two copies, once for each bezel. ...
thingiverse
Even with all the Kindle stands on thingiverse I couldn't find one that worked for me. ... This one is slanted at a 16 degree angle and works best at shoulder or head height.
thingiverse
This is a stand for your kindleFire or any e-reader, iPad, iPhone, and just about whatever. Enjoy! Instructions Open the included STL file with your favorite g-Code software, which will be already...
thingiverse
I wanted a kindle fire stand to attach to my Printer to run Octoprint touch UI on. This is a very simple model that has holes in the bottom for attaching it to a Frame or securing it to something. I have included both Horizontal and Vertical...
thingiverse
This is a tabletop stand for a kindle fire. Use in pairs. Instructions Increased HBP to 110 deg C. Printed w/o rafting. ...Used 4 shells and 25% infill w/0.27 layer height on 0.4 mm nozzle.
thingiverse
This is a simple and compact stand for the paperwhite. ...Perfect for travel.
thingiverse
Stand for Fire HD 8 10th Gen tablet, useful for home assistant interface
thingiverse
My second take at the Kindle Fire snap-in collapsible stand. The previous version used 4 parts that used snap-in hinges in two locations, that could be a bit delicate. This version uses one less part, with larger diameter rods for pivots. Changed...
thingiverse
It was specifically designed for the Kindle Fire 7 Tablet, but I assume a variety of 7" tables should be compatible. It attaches easily to the tower via the two screws near the front that hold the top plate to the tower (Near the extruder). This...
thingiverse
I'm using an original Kindle Fire tablet as the monitor for my front door security camera, but I didn't want to commit to anything as permanent as mounting it to the front door or a wall, so I figured I'd mount it on a stand near the door, and a...
thingiverse
... this with a .8 nozzle,(a .4 will work as well) with 2 perimeters. ...at a .6mm layer height. I would use 4 perimeters with a .4 nozzle. layer heights of multiples of .2 would work best. there are holes for 10mmx3mm magnets to hold the stand in place.