stand for mac mini 3d models
2307805 3d models found related to stand for mac mini.thingiverse
Small table for setting an iPad over a Mac Mini. Sized to max out my Ender 3 build plate. ...May need to be scaled down for fit.
thingiverse
Since I plan to put a tiny SSD drive below the Mac Mini I made an alternative version with a hole large enough to pass an USB cable through. Both designs are also available in a slightly taller (20mm vs 16mm) variant. Bed adhesion can be...
thingiverse
I needed something to stand my new mac mini behind my monitor and taking up as little space as possible on my desktop. This design did the trick. There is a cable stay in the back that is meant to hang over the edge of the desk/table. ... If you...
prusaprinters
I found the original design useful but slightly flawed in design: whenever I would move the Mac Mini, the legs would fall over, so I combined two legs with a simple rectangular block in Tinkercad.
thingiverse
A cooling stand for Mac mini (Late 2018) with a 140mm friction fan mount. You may want to print the top_test.stl first to calibrate your 3D printer. The plastic bottom cover should be removed from your Mac mini. ... My Mac mini with i7-8700B has...
prusaprinters
Simple to print (ABS suggested due to heat) for the Mac Mini 2012 edition to allow for extra air flow under the unit. I find during intensive work (video conversions especially) the bottom of the unit gets very hot. ... I have a fan nearby,...
thingiverse
... desktop. ...One for Mac mini that is behind the display with slot for storage accessory. Another under the display facing forward for the Apple DVD. ...There are two versions of the DVD holder, the second including a slot to also hold a USB hub I have.
thingiverse
Ergotron's original Small PC Mount interferes with the arm. ... So I made a mount that doesn't interfere with the arm when the Mac mini is mounted on the Ergotron LX series pole.
thingiverse
Gives You more space on the desktop. ... Use PETG or PLA to avoid shrinking/warping. Linear supports needed for the Base part. 0.3 mm layer height, 4 shells, 25% infill or above. ... Holder part to be ptinted upright (takes a long).
cults3d
Gives You more space on the desktop. ... Use PETG or PLA to avoid shrinking/warping. Linear supports needed for the Base part. 0.3 mm layer height, 4 shells, 25% infill or above. ...Holder part to be ptinted upright (takes a long).
thingiverse
compact vertical stand for mac mini designed to be srewed into a desk
thingiverse
I designed this modern looking stand for my Mac Mini 2018, it allows better cooling and vertical position. ...Stands very stable.
thingiverse
I was looking for a simple stand for a Mac Mini server, one without too many curves or overhangs so easy to print without supports. I found the Mac Mini Foor by codiourso (thanks!) and they had kindly included the SketchUp source file. After...
thingiverse
Basically Mac mini M1 stand with usb-c hub with ssd enclosure - added MacBook Pro 16" stand
thingiverse
... base, which has a deliberately undersized gap. This makes the side supports 'snug up' against the mini. It also has a built-in 3 degree tilt which seemed best for making my Mini's upright. https://tinkercad.com/things/hzIxmbA5uTP-mac-mini-stand
thingiverse
I remixed the M1 Mac Mini mount to remove the blocking of the air intake, and added feet to mount for my personal project.
thingiverse
My Mac Mini (2011) was overheating so a designed a base to give it airflow. This base can be made in two prints on a 6"x6" bed. The surface area supporting the Mac does not change, and the center of mass is low so I do not believe it will have any...
thingiverse
Support can be printed in PLA or PETG. ...No supports are needed. It fits Mac Mini 2018-2019 with 36mm width. My design has 36.5mm spacing just to make it easier to put Mini in. ...
thingiverse
These feet can be attached to a 140mm fan or a 120mm pc computer fan and then the mac mini can be sat on the top of the fan improving cooling. ...
thingiverse
My 2018 mac mini is great, but the airflow isn't great. ...I threw this together to lift it off my desk a bit, and it seems to be helping.
thingiverse
... avoid scratches. Printed with 25% infill in PLA Using on a 2020 Mac mini (It should work with 2018+) You need to print Two of these ;) Felt padding used: https://smile.amazon.com/gp/product/B00YN18DRY/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
thingiverse
This mount allows the Mac Mini to stand upright. ... Made for my 2020 Mac Mini (I believe it's the same size as the 2018 Mac Min. ... The mount does not block the circular air intake of the computer.
myminifactory
This mount allows the Mac Mini to stand upright. ...Made for my 2020 Mac Mini (I believe it's the same size as the 2018 Mac Min. ...The mount does not block the circular air intake of the computer.
thingiverse
... second design. Feedback is appreciated. 4/4/2022 - Uploaded a V3 file for blank face for the stand (removed Mac Mini M1 lettering). Redid the vents a little. ...I also provided the Fusion 360 file and the Step file for any modifications by others.
thingiverse
Mac Mini 2018 Cooling Stand with space for a Samsung X5 SSD Drive. Require one 120mm x 25mm fan, four M4 screws for mounting of the fan. No support is needed when print. ...I use 20% fill.
myminifactory
This is a simple single part print for a stand to hold two post 2011 Apple mac minis. I've added a little wriggle room (1mm) for the macs so no post-processing needs to be done on the print. ... Happy printing!
thingiverse
To mount the Mac Mini on the back of the iMac I needed a holder and a way to mount this holder so I designed a bracket that clicks on the iMac stand and allows the mac mini holder to be attached. The set is very rigid. Mac Mini power button can be...
grabcad
This is a Mac Mini stand with built in flash reader. ...The reader is a Hama usb 2 flashreader. The Sketchup file contains the stand, the reader print and a simple version of Mac Mini You can use if You want to tailor it to another reader!