standee bases 3d models

(look at that counter retention in photos) * Even thinner with new HP counter post (look at the comparison in the last photo, this was to preserve post strength with a thinner number dial) *V3* * Keyhole socket * Labeled +20 counter *V4* * Decorated...

(As per request, I added a plain disc.) These are modified Gloomhaven bases — I shrunk the base to be 33mm. I re-scaled the numbers to fit the new dial bottom, and slightly moved the conditions shelf in, to fit on the new dial top. I added a hole in...

These are standee bases for enemies in Gloomhaven that allow you to track the monster's health. This is a slightly smaller version of chanson836's "Gloomhaven Boss Standee" in order to better fit inside the GH hexes, while also keeping the numbers,...

Included in this thing is four different versions of hex standee bases and their openscad source. The purpose is to hold a standee card, either use dice or the spinners for a life counter, and hold condition tokens. I used the following as...

Just some simple FDM printable bases to improve your QoL while using cardboard standees from a popular mecha tabletop game. ... Enjoy!

Just some simple FDM printable bases to improve your QoL while using cardboard standees from a popular mecha tabletop game. ... Enjoy!

A standee base for paper miniatures. This base is designed to accommodate standard printer paper or lightweight card stock. ...It's not meant for thick cardboard/chipboard standees.

I created this standee base (specifically for the Gloomhaven JOTL standees) to fill the space of a hex on the scenario board. ...I also wanted the fit of the monsters to not be extremely tight.

... New base with printed numbers. ... ----------------- This is a remake of the Gloomhaven standee base to allow for HP greater than 29. This base goes up to 99. ... The top and bottom pieces are snap connects, and the ring spins around the center.

These are standee bases for the game Dungeon Twister. The 'Basic' file fits the thin cardboard standees from the base set that are .5 mm thick and the 'Other' file fits the wider standees from the expansions (1.2 mm). Both include slots for...

Couldn't find a good, simple, paper standee base so I designed one! This is made for paper standees made of heavy stock paper that's doubled up aka a paper standee that's double sided (you'd print your standee head to head then fold along the line...

My buddy sent me a link to the broken token flying standee base and it's way cheaper to make your own. I don't have any translucent filament, but it would probably look pretty cool to do it that way if you have it. It was modeled using OnShape and...

Another standee for Gloomhaven.

Gluing the paper circles to the base with a small amount of super glue, then pressing the two halves together. Future developments: 1) Eventually, I want to add the ridges that @hein0170 added. ...It would probably help with gripping the bottom...

Plaid Hat Games, the company behind the great board game "Dead of Winter", is not selling extra standee bases yet, so I wanted to make my own on the 3D printer. Instructions File made in Sketchup.

This is a standee or base for monsters in Gloomhaven. I liked the ideas from lane182 and thetruenelson to have a base without the need for dices but with an HP-tracker. For each standee you have to print a top, mid and bottom-part. ...I printed the mid...

3d files made in Autodesk Fusion 360. PDF with circular HP number disks is made in Inkscape. I printed it with 0.2 mm layer height and 80% infill. ...The pdf is the right size if you print it on A4 sized paper with no scaling.

... bases are approximately 1.31" in diameter. ...I modified the top portion of the 2-part flying standee base made by Nuelle to fit a diameter of up to 1.4" so that I could use them with my game's printed standee bases!

We've been using chanson836's standee bases for 20-30 scenarios, and we've had a problem with the bases becoming loose and falling apart when moving monsters around the board. I've altered the design so the base and the post are separate from the...

I’ve tried many of the Gloomhaven standee base designs and liked [the one by JimmerJammer](https://www.thingiverse.com/thing:2477756) by far the best. However, I also really liked the slots for effect tokens I saw in [thetruenelson’s...

A standee base for use with the round enemy tokens, player shield tokens and hexagonal ruin tokens. The same design works for all 3. I found the shields quite difficult to see sometimes, and also just wanted to add a little more verticality to the...

I’ve tried many of the Gloomhaven standee base designs and liked the one by JimmerJammer by far the best. However, I also really liked the slots for effect tokens I saw in <a href="https://www.thingiverse.com/thing:3133406">thetruenelson’s...

... (print and play) games. ...25mm circular base. Includes the OpenSCAD source so you can easily modify. Example minis were created by using HeroForge.com to design them, turn off base and screenshot. ...Easy way to make nice grayscale custom figures.

25mm circular base. Includes the OpenSCAD source so you can easily modify. Example minis were created by using HeroForge.com to design them, turn off base and screenshot. ...Easy way to make nice grayscale custom figures.</p> <h3>Print Settings</h3>...

fat_tracker_20.stl => player power/ghost tracker fat_tracker_36.stl => player and enemy vita tracker fat_tracker_peg.stl => peg to fit either tracker board fat_standee_base.stl => Replacement standee base to match colours with tracker...

* fat_tracker_20.stl => player power/ghost tracker * fat_tracker_36.stl => player and enemy vita tracker * fat_tracker_peg.stl => peg to fit either tracker board * fat_standee_base.stl => Replacement standee base to match colours with tracker *...

Leider hat das Original dieses Remix die Pappmonster beim Einstellen kaputt gedrückt. ... Bei diesem Remix wird die Pappe nicht angeritzt, die Figuren/Zustände aber halten vernünftig

I remixed hein0170's design to have raised numbers around the base, making it very easy to print with a color change at the point where the numbers start. Note that I printed the bottom pieces with a 0.25mm nozzle, as the numbers are very tiny. ... ...

So I figured that it would be easier to keep them apart with different coloured standee bases (since some of the characters look kind of similar). And just for the fun of it I also put the first letter of the type of character on the base. So...