starbucks straw toppers 3d models
9892 3d models found related to starbucks straw toppers.cults3d
Barbie Starbucks straw topper! 🥤 COMMERCIAL USE IS ALLOWED! 💰 Please also check out my Patreon and other models! ... https://www.patreon.com/WE_3D
thingiverse
This is a Starbucks Straw Topper. ...Honestly its my first ever creation on TinkerCAD and I haven't had the chance to print it, so if anyone gives it a shot and has suggestions PLEASE feel free to give your input : D
thingiverse
Small starbucks inspired straw topper for plastic straws that are 8.5mm in diameter, print orientation with the lid side on the bed
cults3d
These are designed that you glue the straw hole onto the back. I did this so you can print with no supports and mass produce them. I use super glue to attach them. ...Two straw sizes included.
thingiverse
the size will need to be adjusted but for the straws I have at home I based it on 7.5mm straw diameter so I hope it is close to that. ... If done on an FDM use the below: layer height: .2 rafts: Doesn't matter Supports: in the creeper and Tweety...
thingiverse
simple Starbucks Straw Lid to keep bugs and bees out off your drinks. ... printet with a 0.4 nozzel
thingiverse
My first upload, not very clean but it will help you find the size of your starbucks straw
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
Actually seen this being sold. ...I knew i could make my own!
thingiverse
Customized version of https://www.thingiverse.com/thing:3045130 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3045130
thingiverse
for anyone that likes Starbucks K-Cup coffee I would use a raft for the filler Starbucks
thingiverse
For anyone that likes Starbucks coffee for the filler I would use a raft to keep the pieces in place
thingiverse
Can't find the right size straw? Just print one. ...About 20 minutes to print one.
cults3d
... straw standing up, without support printing. ...I used Pla Filament for this. The straw can be cleaned with a normal straw cleaner and is waterproof. After cleaning, it is reusable. ...The angled mouth part makes it easier to drink with this straw.
thingiverse
Designed a basic bumper plate as a straw topper for a starbucks cup. Print at 105% scaling to fit the starbucks cup, otherwise scale as needed for your project. ... White nail polish was used for the lettering
thingiverse
This is a basic straw: it is kinda short but can be scaled. You may want to sand it before using it. ...It can also be used as a tubular structure for projects because it is fairly strong.
thingiverse
Shorter Straw design. Intended for a 20oz YETI/RTIC cup. Has stopper so it doesn't fall out of the lid. ... This is the second thing I have designed so if it is bad, I'm sorry :P
sketchfab
Textures: 16 × 16, One color on texture: blue. ...Rigged. Materials: 1 - Straw Smooth shaded. Non-Mirrored. Subdivision Level: 0 Origin located on bottom-center. Polygons: 11008 Vertices: 5504 Formats: Fbx, Obj, Stl, Dae. ...I hope you enjoy the model!
thingiverse
I couldn't find a decent straw to print so I made one myself. It is 210mm (about 8.27") which is the perfect height for most drinks. ...The photo of them in my hand makes them seem smaller than they actually are!