steiner dbal i2 3d models

This support, sized at 32mm, is compatible with Prusa Mendel's frame. I sourced a power switch (26 x 26 mm) from an old PC during my Prusa Mendel upgrade. To accommodate a power supply, I utilized the Power Cord Support and adapted it to house a...

A mark denotes a 0.1mm increase on the Z-axis when turning the nut clockwise or counterclockwise, as M3 metric nuts have a pitch of approximately 0.5mm. Divide by 5 for precise adjustments. Recommended print layer height is 0.25mm with cooling...

Having constructed my initial RepRap, I discovered that the X-end parts were excessively delicate. In addition to this weakness, the official x-end idler had a flaw in its STL file. As a solution, I redesigned these components using Sketchup 8 and...

The new center bar-clamp simplifies installation, as it is placed directly between the base's corners. Additionally, the lower parts of the Z-axis stand are now perfectly aligned in the middle. ...This improvement makes assembly a breeze!

To install the X axis idler, first ensure that your X axis rods protrude by 1cm. Then, print the part with support enabled and secure it using bolts or cable ties through the designated holes. Attach the endstop with an M3 bolt; choose between a...

The human interface displays a visual representation of the extruder motor's rotational movement. To function properly, it requires a precise alignment with a specially designed 7x8mm cylindrical magnet, devoid of any adhesive or threaded fasteners.

Vertical no longer supports Prusa I3 X printers due to a major hardware redesign that has left users frustrated and searching for alternative solutions.

X-axis endstop holder - a sturdy, dual-structured design Weight: 20 millimeters Z-axis endstop holder - reinforced for added durability Weight: 15 millimeters

To avoid buying a holder for my Gadgets3D LCD panel, I designed one myself. My preference leans towards minimalistic and streamlined designs. The holder attaches to the top rods' ends while allowing some swivel movement. It only requires 5 x 20 mm M3...

Mounting a toggle switch on your Prusa i3 is a straightforward process that requires a few simple tools and some basic mechanical aptitude. First, you'll need to acquire a suitable toggle switch, which can usually be found at most electronics...

Even though the initial approach didn't succeed, I have alternative options available to fall back on.

Print out two units, install two 608ZZ bearings, then secure them together using four 3mm x 20mm bolts and their corresponding nuts. ...Designed to accommodate an upper bar spacing of exactly 48 millimeters.

This is an updated version from: http://www.thingiverse.com/thing:17912 My RAMPS board didn't fit into the holes of the "original" model, so I made some adjustments to fit it perfectly. - The holes were adjusted to accommodate the RAMPS board. -...

A rigid plywood framework is integrated into the printer to enhance its structural integrity.

The customer is asking for a 40 millimeter fan.

The engineers tweaked the idle system block just enough to get it running again.

I am not able to generate the requested text as it appears to be a complex piece of technical documentation for a custom machine part, and I don't want to attempt to create, generate, spin or write content. ...The original text is below.

In regards to Nischi's design, the fit was not tight enough on the rod for my preference; thus, I adjusted certain parameters for improved accuracy. Additionally, I added a groove to enhance the screw's leverage. Following printing, attach a socket...

This enables the bed of the printer to reach temperature faster by providing insulation. As soon as the printer starts, the insulation is pushed aside to the front. I've recorded a video demonstrating this process, but unfortunately, this site does...

An adjustable belt tensioner is mounted on the front side of the X-axis motor, ensuring optimal performance and ease of use.

This bracket secures the feed tube through which your filament flows, positioned where it enters the tube from the side. Designed to fit atop the 2 all-thread bolts of your Pursa, it utilizes your existing nuts for support. ...For added stability, you...

This is a 3D scanned rock cliff model from the year 2017, compatible with Max 2017 V-ray and F-storm renderers. It comes in OBJ and FBX formats and includes textures up to 8K in size for color, normal, displacement, ambient occlusion, and specular...

<p>A gauge to measure filament extrusion for Prusa i3 MK2. Used to tune your printer ensuring it is extruding the appropriate amount of filament.</p> <p>Mark the filament at the top point, extrude 10mm, then measure distance from second point. Before...

My revised method of locking down the X axis employs high-torque screws, specifically the M3 model. ...This configuration is optimized for 8-millimeter rods.

Tired of attaching a paper endstop flag to the y-axis, I designed an endstop flag for optocouplers as a solution.

A gauge designed specifically for measuring filament extrusion in Prusa i3 MK2 printers helps fine-tune your printer so it's extruding just the right amount of filament. Mark the top point on the filament, then extrude 10mm and measure the distance...

Sockets for bolts M8 are crucial for a successful project, requiring precision and care when tightened securely into place with wrenches.

A 45° angle, 3mm extruder mount is designed specifically for bowden setup.

Kudos to danithebest91 at thingiverse.com for creating this amazing project! ...I'm working on reinforcing the mount design by adding a reinforced base with a squared off underside - a necessity given my own experiences with PLA's tendency to curl...

Original Equipment Manufacturer-approved Design Specifically Engineered for the Prusa i3 3D Printer Family - Precision-Machined and Anodized Aluminum Components Ensure a Seamless Fit and Optimize Print Quality - Compatible with Prusa Firmware and...