stem bridge project 3d models
272032 3d models found related to stem bridge project.thingiverse
This is just an example used in my Middle School curriculum. Feel free to add suggestions/download for use. *Please let me know if there are any problems. ...I'm still new to the 3D Printing world.
thingiverse
*I did not add a support beam on the second column on both sides simply because I was planning on laying a small road in between so the students could test various loads with different vehicles crossing their bridge. This can be altered very easily...
thingiverse
This is our bridge project. Our bridge is the second best in the class. Have a ratio of 1000lb/g. There is two type of members. One is 75% infill another is 100% infill, I show both of them in the top. They all have a 0.1-inch diameter. I'm so...
thingiverse
Every members are print at 90% infill, our weight is 38.6 Pound and ratio is 266. ...Our bridge is supersize me because it work out well at last since we had do reprint and have some issue with it but it still show a pretty good job.
thingiverse
This bridge was the starting design for students to improve upon as part of a public schools STEM project lead by a public and private partnership between the: 1. the US Army Engineer Research and Development Center (https://www.erdc.usace.army.mil/)...
thingiverse
... certificates at the end of the year. ...Print out 3-D awards. I give this badge to my top 3 toothpick bridge builders. Instructions Prints using .20mm and 10% infill. ...Prints in less than 1 hour.
thingiverse
Eight of the long members are 100 percent infill; all of the short members and four long members are 25 percent infill.The weight of the bridge is 36.9 grams; the weight of the weight is 8890.4 grams. ...The load to weight ratio is 240.9.
thingiverse
This was an 8th grade 3D modeling project. This bridge was able to hold up to 17 lbs of water. ...Students had to design the model in SketchUp.
grabcad
during Mechanical engineering study model of Bridge locking mechanism
cults3d
This project, found in MakerBot in The Classroom (http://www.makerbot.com/education), focuses on designing 3D printed connector pieces for building a balsa wood bridge. ...You can download the entire lesson, 123D_Design_project.pdf, from the Thing...
thingiverse
This was a semester-long AutoCAD IV project for a student entering a Civil Engineering program next year. The bridge held 5 + lbs. on each span (live and dead weight). ...
thingiverse
... two different ways to create a 3D object in 123D Design? References https://sites.google.com/a/fz.k12.mo.us/8th-grade-career-and-technology-education/engineering-bridges http://www.sciencebuddies.org/science-fair-projects/project_ideas/CE_p011.shtml
grabcad
Did this for a friend, her kid needed to make a replica of the golden gate bridge for school, is made of cardboard, elastic, straws, nylon and paint. ...Using glue and staples.
grabcad
My first non-school work. ...I started a few weeks ago in school with rhino and i'm a fan of bikes so i made a Stem. ...I hope you like it!
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=45424 Instructions Using the following options: width = 50 length = 100 edge = 5 line2 = Summit line1 = STEM 3/19 holeRad = 5 tagThickness = 10 tagH = 19 radius = 15 Font = write/orbitron.dxf...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=739573 Instructions Using the following options: line5 = line4 = line3 = line2 = line1 = STEM border_thickness = 3.6 bar_length_trim = 0 outlineextruder = extruder1 font_outline_width = 0.5...