stepcraft cnc 3d models
43758 3d models found related to stepcraft cnc.thingiverse
rack to hold all the tools for a Stepcraft cnc you will also need 2 3 inch 25-50 8020 8 1/4-20 screws
thingiverse
This is a modification of an original design by Alex at 3d-pro.eu http://3d-pro.eu/diy-suction-stepcraft-2-for-kress_amb/?cn-reloaded=1 This design maximizes the aspiration of the Stepcraft CNC but the original design had problems with the magnets...
thingiverse
The stepper motors on a Stepcraft CNC have a drive-shaft on both end. The diameter is 5mm and it is long enough to hold the knop. The STL file has 5mm diameter hole but it is necessary to redrill it. ...Also the hole in the shaft needs a M3 screw...
myminifactory
The original spring steel clips that held the Z axis power cable in place on my Stepcraft 840 CNC weren't working too well, so I replaced them with these super sturdy clips. I used pliers to squeeze them enough to pop into place in the CNC's rail.
thingiverse
With a small Stepcraft CNC milling machine it has been frequently tight to place the fixture properly. Also aligning the stock along the Y axis is often important. Hence I created 5mm high extra short distance blocks, claws, and space-saving...
thingiverse
CNC Vacuum system made to link two Stepcraft machines to a single wet/dry vac. Everything was printed in PLA or another hard material except for the O-ring and Vac cap, which were printed in ninjaflex. The simple valves are used to focus suction...
thingiverse
https://www.ebay.ca/itm/SPRING-LOADED-PCD-DIAMOND-DRAG-ENGRAVING-TOOL-CNC/142851020584 I made my own spring loaded bit by using a linear bearing and a collet extension, now I can add all kinds of bits, mainly those really cheap carbide tips for...
thingiverse
Plug and Play: Stepcraft CNC Proxxon Exhaust Adapter. Designed for Proxxon Tool adapter. May work with other adapter too. Outlet is 13mm outline diameter and 9mm inline diameter. ... Also check out the SLIM-Version of the adapter:...
thingiverse
This is a crosshair laser mount for the standard Stepcraft CNC tool mount, based on an idea by mikath in the Stepcraft forum: https://www.stepcraft-systems.com/en/forum/software2/3245-cross-laser-and-uccnc I liked the idea of using a local...
thingiverse
Digital dial holder for Stepcraft 2/840 cnc. Holder outer diameter 43 mm Holder inner diameter 8 mm Holder can hold Mini Engraving Point from Stepcraft, item nr. ...12278
thingiverse
Foot/ holder for stepcraft 840BE. Supposed to keep it from falling of the table/ hold it in position. ...
thingiverse
Adapter for exhaust fan, you can use a vacuum cleaner domestic... ... If you wish you can decrease his height to adapt with his drill and splinder
pinshape
Summary Adapter for exhaust fan, you can use a vacuum cleaner domestic... ...If you wish you can decrease his height to adapt with his drill and splinder How I Designed This
thingiverse
Simple Laser mount for Specraft CNC mills Print Settings Printer: Davinci 1.0 Rafts: No Supports: Yes Resolution: 0,2mm Infill: 35% Notes: Filament: Annofill ABS, Orange Nozzle Temp: 235C Bed Temp: 95C
thingiverse
Plug and Play: Stepcraft CNC Proxxon Exhaust Adapter. Designed for Proxxon Tool adapter. May work with other adapter too. Outlet is 13mm outline diameter and 9mm inline diameter. ... Also check out the bigger Version of the adapter:...
prusaprinters
Which collets will fit?401E (OZ8), DIN 6388AFound in spindles/routers from Kress, AMB, Isel, Mafell, StepcraftEach position will accept collets with or without nut attached (tested with Kress/AMB nuts)A short type 17mm-spanner will fit into the...
thingiverse
Dust shoe Kress 1050 FME-P The Kress 1050 FME-P has the ER-16 Collet system and therefore the clamp nut has a diameter of 25mm instead of the 18mm on the normal Kress. So, the old dust shoe I had is of no further use because there was not...
thingiverse
in case your spindel is a bit to long and the motor gets blocked when everthings tighten this spacer fits under the motor. I used the 0.4mm version, added the 0.6mm Version just in case. ...Printed in TPU.
thingiverse
There is a small plastic spacer under the screw head that tensions the exhaust port for the HF-500 and MM-1000 spindles. Since there is a 3mm gap under the spacer, any excess torque on the screw will flex the plastic spacer and snap it. This is a...
thingiverse
I'm really happy with the original design and everything fit very nicely. Thanks Hobbyman19! I just encountered two problems that I solved for myself. First was that my brush was to short to reach the ground when using long router bits. So I made...
thingiverse
Customized version of http://www.thingiverse.com/thing:44850 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44850 Instructions Using the following options:...
thingiverse
Customized version of http://www.thingiverse.com/thing:44850 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=44850 Instructions Using the following options:...
prusaprinters
Although the Stepcraft CNC Routers have decent protection of the gantry rail by the rubber flaps, I had the issue of chips entering. These chip guards cover the part were the rubber separates when the gantry moves.Print the part straight up and...
grabcad
T-Nut Plate from CNC milling machine Stepcraft 600 Black Edition
thingiverse
Nez d'aspiration pour CNC Stepcraft.Je l'ai fait en 3 parties pour éviter les supports. La Cyano colle le PLA très vite et très bien. Donc pas de soucis pour l'assemblage. Attention la photo n'est pas tout à fait la bonne pièce (1ère version) mais...
thingiverse
Exhaust-System Adapter for all Stepcraft cnc milling machines 2nd generation with a Kress dremel. Works great! ...See my german article for more information: https://www.stepcraft-systems.com/forum/zubehoer/5360-absaugvorrichtung-aus-dem-3d-drucker
thingiverse
Adapter to mount tools with a 6mm shaft in the clamping collar of a Stepcraft CNC machine (diameter 43mm)