stepper driver 3d models
34022 3d models found related to stepper driver.thingiverse
Device to help you keep the stepper-driver in place during soldering.
grabcad
External model of Digital Stepper Driver 1.0-4.2A 20-50VDC for Nema 17, 23, 24 Stepper Motor.
grabcad
The ULN2003 Stepper Motor Driver, Not 100% but close enough for me to mock up my project.
grabcad
This mount will hold 4 TB6600 style stepper drivers. ... The mount incorporates a fan and ventilation holes to keep the drivers cool.I printed mine with a .8mm nozzle and .4 layer height with PLA.
thingiverse
A fan duct that snaps over a row of four stepper drivers. Uses a 30mm fan. ...My drivers were getting up to 170F during longer prints, after installing this they only get to 120F.
thingiverse
A ring designed to fit a relatively standard style of stepper driver. ...Can be friction fit, but glue is recommended if you dont plan on needing to use the driver at some point.
thingiverse
rack for 4 m542h stepper drivers. has embeded m4 nuts fro durability. and 6 mounting ponts for the bracket. just makes mounting them a little easyer. ...im following up with a duct and fan mount for this assembly later.
thingiverse
With this item, the stepper driver gets always cool fresh air. Including helper for print without PVA Instructions Print with ABS 0.3 or smaller layer. At the end you can remove the helper...
cults3d
rack for 4 m542h stepper drivers. has embeded m4 nuts fro durability. and 6 mounting ponts for the bracket. just makes mounting them a little easyer. ...im following up with a duct and fan mount for this assembly later.
grabcad
Closed Loop Stepper driver.Some components modified from other works, (LED, Terminal Blocks have major edits, 3.5mm to 3.81mm pitch.Stencil for cover from scan included. ...Enjoy!
thingiverse
This is designed for the Leadshine M542 stepper driver and will also work with the Chinese dq542ma Stepper Driver. It would also work with Drivers whose mounting hole are 12mm from the edge of the case and are less than 40mm thick (as shown in the...
prusaprinters
This is a simple Ring design to place a stepper driver on. That way you can show everyone if you were able to get an TMC5160pro. Printed in TPU for a nice fit. ...I added the f3d if you would like to edit it for you finger size. </p><p>Perfect for...
thingiverse
I seem to have collected a few stepper drivers & they were rattling around an old GT2560 driver board box & starting to get damaged. This is just a simple box insert that you can put small parts/tools underneath & the drivers with the taller...
thingiverse
this is a stepper driver cooler for the lerdge 3d s 32 bit mainboard (3d printer controller) it useds a 30x30x10mm fan! if you'd like me to make it so a 40x40 gfan will work please don't be afraid to ask! i am in the process of making a slide and...
thingiverse
This is a mount, (bumper) for ULM2003 Stepper Motor Driver. It uses 4, 2.5x4 mm screws to mount the PCB and 2, 3 mm screws to attach the mount to your project. ...The back of this mount is fully covered to prevent shorts.
thingiverse
For a while now, Ive been trying to design my own printer electronics, and wanted to test that all of the connections were being made to where they were and that everything was working as it should up to the stepper drivers, so I designed this. I...
thingiverse
:) Compatibility: Makerbot Motherboard; Stepper Motors require standard 0.1" header Instructions Refer to the documentation of its father, PSMD (Pololu Stepper Motor Driver) Triple Axis Driver Note: R20, R21 are labeled as 1k Ohm, but should be set...
thingiverse
ULN2003 Stepper Driver Double Holder Here is a simple holder for two ULN2003 stepper driver boards. ... Both boards are held with an M3 screw.
thingiverse
2018-05-21 updated : for missing front side parts stand alone stepper driver case
thingiverse
DIN Rail mount für DM542T Stepper Driver Mount with M3 screws