stepper motor camera mount 3d models
483341 3d models found related to stepper motor camera mount.thingiverse
Mounts on the Y Axis stepper motor and designed to hold this camera. ... https://www.amazon.ca/gp/product/B076KCZRDS/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
thingiverse
Designed to be attached to the x-axis stepper motor by replacing the top two screws with 45cm M3 screws. It is slightly offset to ensure a better camera focus. The light bar is designed for a 160 mm adhesive LED strip. If you don't want to use...
thingiverse
Small remix i made to hold a Huawei scrap phone into place for use a webcam.
thingiverse
... out the original's camera parts to hold the actual camera board. Bonus: if you have an extra stepper motor damper, you can use it on the camera. ... 3/21/19: added a flipped model in case you want the camera slightly higher up rather than lower.
thingiverse
Added new version to mount camera and added the camera mount. The opening is 16x8mm and 16.5mm long. The camera mount is slightly smaller, 15.5x 7.7mm to make it fit the opening otherwise you have to jam it in. With snap-in holding "tabs"(?) for...
thingiverse
The new and improved version is available here: https://www.thingiverse.com/thing:4547074 I designed this pan tilt mount for my Canon EOS 250D DSLR camera so I would do some motion controlled shots, timelapses and panoramas. The brain of it is an...
prusaprinters
I designed this mounting bracket to attach a Logitech webcam onto my pen plotter. This was part of my Master's Thesis for my studies at the University of Lapland.The complete thesis “Numerically Controlled Pen Plotters in Art : Building an...
prusaprinters
<p>Prints without support, align the bottom to be flat.</p>
thingiverse
This motor mount is for a generic stepper motor for use on my Arduino robot
thingiverse
Left and right bracket designed to mount a stepper motor to a 20mm aluminum extrusion
thingiverse
This is a Stepper Motor mount I designed to mount the stepper Motor for the Extruder to the ground plate of my printer. ...Used Hot Glue to mount it, but also M3 Screws can be used.
thingiverse
Stepper Mount and stepper driver case for http://www.ebay.com/itm/1pcs-Stepper-Motor-5V-4-phase-5-line-Driver-Board-ULN2003-for-Arduino-Perfect-/131469911265?pt=LH_DefaultDomain_0&hash=item1e9c37a4e1
thingiverse
simple stepper motor mount for a rep rap printer This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/jjAaNbzsAxI
prusaprinters
This is a mount for small stepper motors like this. It is meant to attach a stepper to any flat surface such as a platform or metal piece. Sorry for the blurry photos. I was taking pictures with my GoPro because my camera was charging Post-Printing...
cults3d
Horizontal motor mount for the NMB Technologies Corporation PG15S-D20-HHB9 stepper motor (http://www.digikey.com/product-detail/en/PG15S-D20-HHB9/P14333-ND/2417057). ... Designed for a custom project.
thingiverse
This is a mount for an Arduino 5 volt Stepper Motor. ...It can be tapped M4 or #8-32 for the motor holes and will take 3mm or #6 screws on the base.
thingiverse
Horizontal motor mount for the NMB Technologies Corporation PG15S-D20-HHB9 stepper motor (http://www.digikey.com/product-detail/en/PG15S-D20-HHB9/P14333-ND/2417057). ...Designed for a custom project.
thingiverse
This is a stepper motor mount with holes for adjustable tensioning all-thread rails. ...This is very helpful for setting up belt drive designs when you aren't exactly sure what drive ratios you'll need.
thingiverse
Stepper motor mount that I designed for my Flashforge creator pro. Printed at 100% infill (could probably get away with less). ...Been in use for a full 8 months of moderate use and no sign of warping or damage
thingiverse
This mount was made for a salvaged stepper motor that I don't believe conforms to standard NEMA sizes. I made the motor mounting holes reversible incase they interfere with the timing belt. Meccano sized holes were made to secure the base. ...
thingiverse
Attaches threaded stepper motor to plank of wood for astrophotography barn door tracking project.
thingiverse
A stepper mount for most normal size (Chinese) steppers. ...The photo is of the extruder steppers that came with the CTC Bizer.
prusaprinters
The original design for the NEMA17 stepper motor mount is from ccox in Thingiverse. Here is his Thingiverse link:https://www.thingiverse.com/thing:2073446
thingiverse
It is a super generic design that will fit any motor and could be adapted to fit almost any vertical mounting surface. The motor is strapped down using zipties, and seems to hold really well. I am going to make a variation to rotate the stepper 45...
thingiverse
This is a motor mount for a small stepper motor such as the one included in the Elegoo Arduino starter kit (linked below). You can use this as a part of other projects whenever you need to hold the motor in place. The screw holes are 4mm in diameter...