stepper motor pulley 3d models

28BYJ-48 Stepper Motor Pulley Made in tinkerCAD from: https://www.thingiverse.com/thing:682418/ https://www.thingiverse.com/thing:4817279

I used this pulley to wind a string using a stepper motor. ...28byj-48 model stepper.

Pulley that fits a 28BYJ-48 stepper motor.

This is a NEMA 17 (or 14) stepper motor mount which supports a 16t toothed GT2 pulley and fits on the end of OpenBuilds (or similar) 20x0 extrusion. It has a mount for an MR105 bearing to take the belt load off of the motor spindle. Change the...

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: teeth = 12 additional_tooth_depth = 0 profile = 10 nut_angle = 90 retainer_ht = 2.5 retainer = 1 m3_nut_hex = 1 idler_ht = 1.5 m3_nut_depth = 2.7...

This is a winch that can be controlled with a rotary encoder. ... https://github.com/brendan234/pully/blob/master/pully.ino https://youtu.be/3rXFwkPwuF4

Customized stepper motor pulley covers for Creality Ender printers.

http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following options: teeth = 12 additional_tooth_depth = 0 profile = 10 nut_angle = 90 retainer_ht = 2.5 retainer = 1 m3_nut_hex = 1 idler_ht = 1.5 m3_nut_depth = 2.7...

I still had to use a workshop press to unlock the pulley on a third engine, so it will be a bit of luck... After a few returns from people who had their extractor broken at the base, I took back the extractor version 2 and I made 2 holes to insert...

Handle: https://www.thingiverse.com/thing:3749185 Pulley: https://www.thingiverse.com/thing:155018 Stepper Motor adapter: https://www.thingiverse.com/thing:34116 There's prob a better way to do this but I'm not a programmer. Board used is a BTT SKR...

This pulley was designed to press fit onto Sparkfun.com's stepper motor (#ROB-09238). It was used to create SADbot, a project featured in my book Making Things Move (www.makingthingsmove.com) that Ben Leduc-Mills and I created for the window gallery...

... to the stepper motor axle and have it centered. I solved this by creating an adapter that friction fit on the stepper motor axle and was just undersized enough to fit snugly in the pulley and when the screws were tightened it was even more secure.

I designed this two piece knob / thumb wheel to help me rotate the pulley stepper motor with my fingers as I clean the hobbed filament pulleys / drive gears from shredded filament bits with a needle or toothbrush. Works great. You will need (2) 3mm x...

I believe the ratio is near 32:1, which makes the blinds go up slow, but due to the cheap stepper motors I preferred it slow and quiet. I do intend on making a faster version. My blinds are really heavy and this does the job. My steppers are...

I designed this pulley for the project: "DIY make claw machine at home". ... Check more guide on my Youtube channel: https://www.youtube.com/channel/UChwNQ-OqSZoVFFfEkylF2Uw

I got 8mm pulley and 5 mm stepper motor. ...What I did, stupid cylinder to connect one to another.

Fits perfectly on the shaft of the 28BYJ-48 stepper motor (no gluing). ...Can be used as a rope pulley.

Here is a custom designed timer pulley for a 12mm wide belt, 20 teeth, and 8mm bore with flat.

This was designed to remove pulleys from stepper motors. First design uses a m4 threaded insert from mcmaster. Second design uses a m4 nut. ...Please note the orientation of the print will affect the strength.

Simple curtain opener for the stepper motor. It can be used to simply pull the curtains - note that when rewinding/returning to the original position, there must be a tension applied to the string so that it does not start curling around the pulley.

30 teeth pulley for GT2 belt with symmetric set screws to avoid off axis deformation. Requires 2x M3 nut and 2x M3 5mm grub screw. ...

This is a pulley I've made for my polar drawbot. I have printed it, and done a lift test. Using thread and a 120g weight it runs smoothly. I am using an Arduino with AccelStepper (setMaxSpeed 1000, setAcceleration 100, setSpeed 200). ... It can be...

A stiffer **stepper motor mounting bracket** and **pulley bracket** for the Y axis of the Wanhao Duplicator i3 Plus (I have a Mark 2) The **stepper motor bracket** utilises a longer centre rear panel screw (M5 x at least 20mm) with a washer and M5...

made a way to connect it with an M3 nut and bolt to the stepper

made a way to connect it with an M3 nut and bolt to the stepper Category: Tools

Basically I made it to the final project of the school. when I get bored, I idly to render some part of my final project. ...please give me criticism and suggestions.thank you

See http://www.instructables.com/id/Designing-a-3D-printed-beaded-ball-chain-drive-pul/ Instructions See http://www.instructables.com/id/Designing-a-3D-printed-beaded-ball-chain-drive-pul/

This model allows to mount a stepper motor damper on the X axis if the motor has a press-fit pulley that cannot be removed without the risk of damaging the motor. You can print a simple stop flag or a mount for a M18 sensor, the distance is X +48...

:-) ******************** This model allows to mount a stepper motor damper on the X axis if the motor has a press-fit pulley that cannot be removed without the risk of damaging the motor. The assembly requires the following fasteners: 2x M3x25...

Customized version of https://www.thingiverse.com/thing:913582 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=913582