stm32 nucleo board case 3d models

Hey,\n\nI'm pitching my electronic case for AM8.\nOne Mofset is sufficient, but it's also compatible with OrangePi lite.\nThe OrangePi lite is a fantastic alternative to Raspberry Pi due to its lower cost and smaller size.\nUnderneath the OrangePi,...

DC jack is this style: https://www.aliexpress.com/item/32857176485.html 3.5mm jack is this style, and connects to the board through a cable i crimped up with a 3 position JST-XH, or you could just solder right to the board:...

Got bored and i remade/remix box for rambo board to fit anet v1.0 and v1.7 board on al profiles (20x40) on my bear anet metal upgrade, still in progress but it fits and look awesome as the original rambo box (atleast i hope so :-)) Print in place...

Human beings strive to design a way of constructing huge objects, such as the wooden board in this instance. My proposal is to link two smaller components together to create one gigantic item, measuring 23 cm in size. ... Print Settings Printer...

The Raspberry Pi Zero (W) is now supported by a modified model that allows it to function as a USB Gadget via the Solderless USB Zero Addon 1.1 Board. This modification has been adapted into various versions with different header configurations. In...

 I used four stick on rubber feet to stabilize the board since the gps module lives under there.  A few dabs of hot glue will keep it in place.  The holes for the screws on the antenna ring and the lid need reamed out to fit the screws.Updated parts...

I'm Excited to Share My First Fusion 360 Project - Full Enclosure for Ramps 1.4 Board! As I Worked on this Project, I Decided to Make Some Changes Along the Way. Initially, I Added a New Rear Panel to Give it a Fresh Look. Next, I Added a Lid with...

... Buttons Two buttons are held in by a toe-like lip so they don't go flying if the case gets flipped upside down. To insert them, put the toe in first and press it in at an angle. Depending on your print, filing or cutting may make insertion easier!

These subtle details not only make the case more visually appealing but also enable it to be printed without support structures, saving time and material. The finished case turned out beautifully, but unfortunately, I had to restart the printing...

Here are some key features of this custom-made case: * No extra hardware is needed; simply slide the RA-35 into place and secure the lid * Strategically placed holes in the top allow for clear visibility of each LED light * No additional supports or...

A simple case for a 2-channel relay with mounting holes on either side is being crafted. To assemble this project, I employed 4mm wood screws, taking care not to apply too much force to the screw holes, as over-tightening can cause them to crack.

This case is for the "ARDUINO TINY MACHINE LEARNING KIT" used for the EdX course "Deploying TinyML" and includes a cover and button. The top is open for sensor and microphone access. The Grove connectors are accessible for expansion. ... ...

Printing notes are as follows: This case was engineered around a 0.48mm extrusion width, giving features added strength. If the case isn't printing correctly, try adjusting the slicer's extrusion width for optimal results. Buttons The two buttons...

To assemble this project, the case and bottom cover must be printed separately using the Brim function with their open sides facing upwards. The front panels included are designed for both thin and thick cases used in the SFG module's design. These...

Case to house the basic components of a desktop PC. Space for micro ATX motherboard, power supply, 1 HDD 3.5, 1 SSD, extra fan, USB, Audio, buttons, etc. Ideal for server PC. Internal reinforcement bars and tight-fitting lid. Trapezoidal shape.

Hy, I propose you my electronic case for AM8. Only one Mofset but OrangePi lite compatible. OrangePi lite is a very nice alternative to Raspberry because is less expensive et smaller. Under the OrangePi you can mount my tension regulator box :...

Custom Camera Gimbal Housing Design Developed Specifically for My Camera System Two Cable Version and One Cable Version Available The Case Features a Secure Lid with Built-In Connectors Holders Two Cylindrical Shafts Keep Connectors in Place,...

... space and provide more convenient access. ... This is a remix of the Minimalist Control Case from jckz82: https://www.thingiverse.com/thing:3127377 Replace the original cable with a longer 10-Pin (2x5) Female to Female 2.54mm-Pitch Flat Ribbon Cable

The top was split into two pieces the middle piece goes around the Dragino LoRa/GPS v1.4 board with two holes for the RF Antenna connectors. The top piece is removeable without powering the piece down or removing the Antenna cable. 4 M3 x 30mm...

The top was divided into two sections; the middle section wraps around the Dragino LoRa/GPS v1.4 board with two holes for the RF Antenna connectors. The top piece can be removed without powering down or disconnecting the Antenna cable. Four M3 x...

I remixed the model so it fits when an OLED display is soldered directly to the board pins.Changed the diameter of the screw holes so that 3mm screws can be used.Added spacers for greater stability.I printed the front with the display side up, with...

If the case isn't printing quite right, try adjusting the slicer's extrusion width.ButtonsThe two buttons are held in by a toe-like lip (so if the case gets flipped upside down the buttons don't go flying everywhere(!)). To insert them, put the toe...

Well, that can be fixed =] Here are some things to know about this case: No hardware required -- put the RA-35 in and snap the lid shut There are holes in the lid placed above each of the three LEDs No supports are required I hope you find it useful...

Well, that can be fixed =] Here are some things to know about this case: No hardware required -- put the RA-35 in and snap the lid shut There are holes in the lid placed above each of the three LEDs No supports are required I hope you find it useful...

A 3D printed soldering station case is a case made using 3D printing technology that is used to protect and house a soldering station. It can be made in different sizes and shapes to protect the soldering station from dirt, dust and damage and extend...

Remixed Case for LCSOFT CY7C68013A logic analyzer clone" by jamesglanville I edited OpenSCAD to remove switch and screw holes, friction fit was tight enough. (set to 0 size to remove) edited screw to allow to use counter sunk screws. added comments...

mark the center of x and y axis on the reference case with a blade and measure distances to the connectors centers with a caliper filling "cuts" array continuing until render seems close enough 4. adjust "down_z" until the length of the legs that...

This is a case for adapting a Spinel IMX290 camera module to a finder scope Celestron 9x50. Camera Module: https://store.spinelelectronics.com/UC20MPG_L60 Assembly instructions: 1. Loosen the screw that secures the camera lens. 2. Position the...

Build custom top and bottom parts for a Papilio Pro FPGA board. With the logic analyzer firmware upload, it becomes a high-speed 16-bit logic analyzer at 200 MHz. When paired with a 16-bit I/O level shifter "Wing", it can handle voltage levels from 0...

Mine was 70 x 40 so I had to redesign it to suit the larger board. This is basically the same design as the others. Nothing new. The Arrow shaped hole is located above the trim pot so you can adjust it without opening the box. I couldn't be bothered...