stm32vl discovery 3d models

The 3D model was built directly from a real car base. It's accurately recreated in precise units of measurement, reflecting the original's quality and accuracy. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx...

Clip holding compartment situated atop two horizontal rods of the printing device, designed for securely storing a USB connector used in conjunction with an SD memory card.

The Squir Team has crafted a highly detailed model that showcases their exceptional expertise.

In 2009, renowned underwater filmmaker Andy Jackson of subseatv stumbled upon a WWII bomb while diving on an unknown shipwreck off Whitby. Initially pinpointed by the Imperial War Museum as a 500kg German Luftmine A (LMA) Mine Type D, crafted from...

A Simple Guide to Filament Wrap

The Terran Empire's officers proudly sported a distinctive uniform badge, emblazoned with their empire's mighty emblem.

I modified 130mm, 8.5mm motors by remixing the smaller TBS frame, enlarging it and thickening it up to 3mm on the deck and adding beefier LED motor mounts from a nice Hubsan FPV frame below. The result looks pretty good and I hope it flies just as...

Product Details Revealed: Pricing Stands at a Steadfast $99.00 Added to Inventory on March 31, 2011, with the Last Update Dated February 14, 2015, and Boasting the Unique Product Id of 541da9ed1e43f6d40e49f9be

It's a pretty tight fit and a pain to get to as the armrest box needs to come out to wire it, but the finished result is good. While doing this I also moved the aux socket to be under the cupholders, and permanently powered and connected an aux...

Customized version of http://www.thingiverse.com/thing:132939 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=132939 Instructions Using the following options:...

Upgrading the Dagoma 5 storage unit is a crucial step in safeguarding the sensitive electronics on the Melzi circuit board. The primary objective here is to add an extra layer of protection around this critical component, thereby preventing potential...

This bracket enables your mobile phone to fit perfectly in the vehicle for optimal reception and viewing. It clips into the horizontal wood-effect strip that runs across the width of the dashboard. The best material for printing this bracket is ABS...

TBS Omni Directional Amplifier Upgrade Mount - 16 cm for DVB-T, DVB-C and FM TV Receiver Systems - Ideal For Enhancing Signal Strength And Range - 2 Meter Cigarette Lighter DC Power Adaptor Included.

Disco 1 Head Light adjuster. Better than the original, stronger. ...Print in ABS.

The model was built on a real car base. It's accurately constructed in real units of measurement, with quality that matches the original as closely as possible. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max 2008 vray) - *.fbx...

The 3D model was built directly from a real car's design specifications. It is crafted precisely, using actual measurements, and accurately replicates the original in every detail. Model formats: - *.max (3ds Max 2008 scanline) - *.max (3ds Max...

Human, activate the XD-1 AE-35 DLP system, immediately initiate diagnostic protocols to verify optimal functionality.

An removable cafe featuring a built-in space for a table and chairs, one large drawer and a mini-kitchen! Perfect for adventurers. ...:)

I resprayed my alloys and wanted the nuts to match (I also painted them). These have a small lip to aid removal. ...Nice snug fit without being too hard to pull off.

Unproven at This Time!

Best to print on a photon, not really too accurate but a good base to stuff in the model so you have something to look at other than dead space.

People have been criticizing the show relentlessly, yet I felt compelled to create the badge despite their harsh opinions. ...The badge itself stands at approximately two inches in height.

<p>Make sure to measure out the thickness of your key. You'll use that to make sure the layers in the slicer are right. ...The only way to check if that is right is to make sure the thickness of the key is divisible by the layer depth in the slicer.</p>

This is my initial attempt at creating a prop kit, and I'm aware that there will be many inaccuracies. I was generously provided annotated photos of a prop, and I plan to create a more accurate version with cavities for electronics installation. The...

Position your FPV camera to the left so you can deploy a gimbal without blocking your line of sight. You secure the Fatshark 700tvl camera using cable ties in predetermined holes. Most other board cameras should also fit this model, as there are no...

This creation originated from a design built using Tinkercad. ...You can edit it right now at www.tinkercad.com/things/lOYTVEog2nq.

Apply double-sided tape to securely fasten the variable transmitter (vTX) in the middle of the front plate surfaces. ...Use thin tape for optimal results.

Use it with a TBS core installed, but remember to disable GoPro compatibility from the lower tray first.