stock bed 3d models

http://www.thingiverse.com/apps/customizer/run?thing_id=332507 Instructions Using the following options: stock_bed_selection = 305 scale = 25 other_stock_selection = 500 shelves = 4 chair_type = 1000 depth = 30 sofabed_depth = 65 height = 30 units =...

USE ABS My bed mat was kinda bent so I made this to avoid buldges or raised parts. ...its not meant to replace the stock clips , although it could, but made to stick the mat to the bed as flat as possible

... I would design me own ones. All of the external edged are filleted the internal ones that come into contact with the bed and heater are not. I am testing clips printed in PLA, but ABS might be better for withstanding the heat from the bed. ...

cable chain bed cover for stock bed corner.TESTED WORKS. ...

I have seen multiple designs for single MGN12 Linear Rail For Ender 3 bed, but haven't seen one using dual rails for better stability and still using stock bed carriage. Due to the fact that the Ender3 bed moves on only 20mm wide frame extrusion,...

This is a remix of http://www.thingiverse.com/thing:376515 to maximize the useful area of the stock PrintrBot 1405 bed. With these X ends and the original Z axis rods you can extend the bed X size to 145mm. See the original thing for instructions and...

This is a remix of http://www.thingiverse.com/thing:376515 to maximize the useful area of the stock PrintrBot 1405 bed. With these X ends and the original Z axis rods you can extend the bed X size to 145mm. See the original thing for instructions...

... Z_MAX_POS 240 #define Z_MIN_POS 0 // Set the boundaries for probing (where the probe can reach). #define LEFT_PROBE_BED_POSITION 15 #define RIGHT_PROBE_BED_POSITION 210 #define BACK_PROBE_BED_POSITION 210 #define FRONT_PROBE_BED_POSITION 50

Update 25.08.2014 V2 Minor changes: Usable area increased to 280mm (Firmware change required) Print bed aligned to bed mount Washer for aligned print bed Instructions Installation guide: Print the following parts: 2 x Bed_mount 2 x Bearing_mount 2 x...

Instructions Print bed mounts with PLA on cold bed on blue M3 painters tape #2090 (See tape roll inner side for the number) at VERY SLOW speed ! This will prevent warping need : 2 x 8 x 400 mm rods (for standard upgrade) 4 x LM8UU bearings Reuse...

This is adapter to enable https://www.thingiverse.com/thing:1828362 to be used with 2 SCS-8LUU instead of 4 SCS-8UU 60% Grid infill Additional Items needed 8 x M4x15 8 x M4x20 16 M4 Nuts 24 Washers ...

I modified this thing:514750 just litle bit

3x corner guides for the stock glass bed with no play (wobble) in the parts. They will fit and hold the glass tight, stopping it from sliding arount when the clips are removed. they help gulide the glass bed in to place, I still use the 4 small...

Here is a quick and dirty way to keep your precious 0.1mm (or other) shim stock flat and easy to use for bed leveling. 1. Print 2. Cut a strip of your favorite shim stock no more than 20mm wide. (I use 0.1mm) 3. Put into holder The holder...

I saw this cool idea to use calipers to help level the ender 2 bed but didnt want to upgrade my mount for the fan. So I remixed this to fit on the right side of the ender 2s stock housing using two M2 x 8mm Screws. Currently printing a test version...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

It has been cut to fit a smaller bed. You will need to print four long pegs and two short ones. You will also need 5x M3 lock nuts and 2 M3x25, 2 M3x40, 1 M3x35 bolts. Use superglue or epoxy on the A and B parts. ...You might have to trim down the notch...

I couldn't stand the stock Micromake glass clips as they were too tall, hence the part fan duct of the stock extruder would crash into them on bigger prints. So I made some low profile glass clips/clamps to hold it in place without protruding above...

This support is for who do not use auto levelling on FSLun Cube and use a glass and did not change the stock sensor for one with more distance of actuation. ... Will need some M3 screws.

Using this mod, you can achieve Auto Bed Leveling on Artillery Printers for FREE using only stock parts (as long as you have a PEI Sprint Steel Sheet installed). No need to spend money on a BLTouch sensor. You can easily use the Z inductive...

This sensor mount is used for Artillery printers like the Sidewinder X1 and Genius. Using this mod, you can achieve Auto Bed Leveling on Artillery Printers for FREE using only stock parts (as long as you have a PEI Sprint Steel Sheet installed). No...

Cover and mount for the stock sensor mod found here: https://3dprintbeginner.com/sidewinder-x1-auto-bed-leveling-stock-sensor/ When doing the stock sensor mod, I went on thingiverse to look at all the different covers to find ideas and models to...

Unlike the paper-under-the-nozzle method where you guess whether that's enough friction on the page or not, or the auto methods where you hope the probe senses the bed before crashing (where the sensitivity can change wildly with the bed's temp), in...

A simple hook to hang things from a bunk bed. &nbsp;Prints just fine in draft mode. ...&nbsp;</p>

... This make less chance of the heat press inserts popping out. Again, thanks to zbrozek for amazing design and providing the files. This is much better than the stupid metal U-bolts that hold the bearings onto the bottom of the bed on stock MK3.

I really liked the original model but couldn't print the longer stock version on my smaller bed , after a few hours of use with the original stockless one i broke it trying to go prone in Pavlov haha, so i decided if i was going to re-print it i...

Minimal support is needed.Ender 5 Plus - Print on the side opposite the PCBA connector opening.&nbsp;These models are tailored to Ender 5/Pro/Plus which have been converted to the ZeroG Mercury One CoreXY system.Ender 5/Pro version mounts to the rear...

One for the Titan extruder One for the STOCK BW extruder The sensor activator works for both versions. Both have premade support added. Only print the sensor activator with black filament ( do not use light colors or translucent ) Sensor: 5 volt...

https://www.thingiverse.com/thing:4920084 UN soporte mas largo, que se me ha quedado corto. ... https://www.thingiverse.com/thing:3972011

UN soporte mas largo, que se me ha quedado corto. ...https://www.thingiverse.com/thing:3972011