stylus pen for ds 3d models

Replacement stylus for DS Lite (does not fit the original DS). Flat bottom for printing. Small tab to keep stylus in place when stored. ... Instructions I printed 100% fill @ 0.1 mm layers.

Reimx of IronHand's Nintendo DS stylus design with corrected scaling. Now 73mm long x 4mm wide x 5.5mm high (including tab). ...It fits nicely in my DS.

I have made a pen clip for my 2-in-1 stylus(ball pen and stylus pen). The diameter of the clip is 9.5mm. The clip may also work for a pen that does not come with a built-in pen clip. ...

Comfy stylus, made for boogie boards, but prolly useful for any tablet devices? ...Includes configurable freecad file.

DS Lite Stylus.

Ds Lite stylus

This is a stylus design for a Nintendo DS (first generation). ...It suits in the stylus holder on the back of the DS and it is very stable.

This was a prototype Sliding Stylus for the Nintendo DS which I've designed. This stylus is too flexible to use with PLA, but it might work with ABS? ... Requires Raft to print.

... Instructions Print on a Mendel/Darwin, Makerbot Cupcake, or other RepRap derivative. Glue to the two parts together with the appropriate adhesive for your material to provide the shoulder that prevents the stylus sliding too far into the DS case.

This is a stylus design for a Nintendo DS (first generation). It suits in the stylus holder on the back of the DS and it is very stable. Instructions I made this one with an BFB 3D Printer. Use no...

This is a replacement stylus for the Nintendo DS Lite. ...It's been designed to print sideways, might need to be rotated 90 degrees, and could use a raft if the bump doesn't stick to the print bed etsy - http://www.16bitgamestore.etsy.com/ eBay -...

Stylus pens clip for Frsky X20 , X20S

This is a Stylus for the Original Nintendo DS. Surprisingly hard to find decent replacements for them, so I made this. Rounded nose to minimize scratching (no clue if it does but not having a point does help). Print the model as is, so you can also...

This is a Stylus for the Original Nintendo DS. Surprisingly hard to find decent replacements for them, so I made this. Rounded nose to minimize scratching (no clue if it does but not having a point does help). Print the model as is, so you can...

made this thumb stylus for my 3ds that clips on my wrist strap. ...this is still a work in progress so let me know if there are any problems with the design.

made this thumb stylus for my 3ds that clips on my wrist strap. ...this is still a work in progress so let me know if there are any problems with the design.

If you don't have a 3D Printer I can make it for you from my stores on eBay and etsyetsy -http://www.16bitgamestore.etsy.com/eBay -https://www.ebay.ca/usr/16bitvideogamestoreI've had issues printing this in Prusa Slicer, Maker Bot's Cura is the only...

Rough model for fitting only.

This is a protective case for my Dell Active Pen stylus. ...This allows it to be stored without damage in bag

Thank you for choosing this 3D Model. ... This is a model of a “Stylus Pen” The model is fully textured in vray, So you will not hang in texture part. Just download and use it. Please rate, when you buy. ...Thanks!

Modeled after the Master Sword pedestal in the Temple of Time in The Legend of Zelda: Ocarina of Time. ...Fits any modern stylus for Wacom/Cintique styluses.

###Stylus Pen for Trimble TSC3 Controller This stylus pen has been designed and developed by a few 3D printer enthusiasts at **Taylors Development Strategists**. The idea was to provide our field crews our own designed and printed stylus pens for our...

... of a conductive filament. ... Perimeters: Three lines perimeter. Layer Height: Medium. Printing speed: Low. Travel speed: Low. Printed with conductive filament:https://ebay.to/2AAWUMf Post on our site:http://horizonlab.co/2017/05/06/mini-stylus-pen/

This remix has a 13mm hole which can fit a Bamboo stylus. ...Print Settings Printer: Kossel XL Rafts: No ...

The g-code only includes three 5.5mm tipped pens and is only meant to be a sample, to show how I printed some of them on my machine. When creating your own g-code I would advise you to use rafts as well as try to have the supports of the...

This remix has a 13mm hole which can fit a Bamboo stylus. Print Settings Printer: Kossel XL Rafts: NoSupports: No Resolution: 0.2mmInfill: 30% Notes: No special settings needed. Category: Office

There are two designs, the cross pattern is more flexible but I suspect it might break easier.The solid print is stronger and harder to get the pen into, but I expect it will soften over time. I stuck the holder using #M Command Adhesive strips.

Post-Printing From Top to Bottom: -Nintendo DS Stylus -Second Print, "HIgh" with 100% infill and line style infill - - -First print, default "Medium" Matter Control settings - - Custom Section Progress... MARCH 26 UPDATE: Our printer...

This is my design for a 3D Printable Stylus for the Nintendo DS Lite. I've designed it to be pre-rotated for perfect printability, and it requires very little to no post processing.   If you'd like one, but have no printed, I am selling them on my...

Thank you so much the16bitgamer for creating this excellent design, I have printed a few and they work like a charm, although a little difficult to print. In fact, in my case PrusaSlicer would simply not even slice it properly, it left it hanging in...