stylus stand 3d models

Wacom Skull Intous Stylus Stand. ...Design is 50.80 mm x 56.58mm x 45.17mm.

One of my first attempts on designing something. ...A small stylus stand you can plug in the USB port of your laptop.

A simple stand for a Veikk S640 stylus

A vertical stand for the Ratta Supernote (Standard) Stylus. Gets it off the table so it can be picked up easily and also so it doesn't roll around (not that it rolls much before).</p><p>As pictured with 0.1mm layers, but it also printed properly with...

A vertical stand for the Ratta Supernote (Standard) Stylus. Gets it off the table so it can be picked up easily and also so it doesn't roll around (not that it rolls much before). As pictured with 0.1mm layers, but it also printed properly with...

This is a digital 3D printable model of one of the GOT dragons – turned into a Stylus Pen Stand. We tried to capture the aesthetic of the dragons that appear in the show, be it Game of Thrones or House of the Dragon. The Stand is designed for Wacom...

... ... This is designed for my wacom stylus but you can also create a ring to fit your own stylus if the diameter differs. I recommend to use marble or dust color for the base, iron gray for the head and brownish for the front part. ... Enjoy!

... I didn't have my keyboard attached. ...I designed and printed this to allow me to stand the stylus on my desk when I wasn't using it. The print settings aren't important. ...I printed mine with 20% infill but you could probably get away with less.

The holder is 12mm internal diameter so will accommodate styluses that have a barrel diameter of less than 12mm.  It's a solid model so that it is weighted and will keep the pen easily upright. ...I would recommend you do not use any infill when...

The holder is 12mm internal diameter so will accommodate styluses that have a barrel diameter of less than 12mm. It's a solid model so that it is weighted and will keep the pen easily upright. I would recommend you do not use any infill when...

Something I threw together in TinkerCAD to hold my Intuos Draw tablet and stylus on my desk :) I'm new to this so any comments/suggestions are always appreciated! ...TinkerCAD Link:https://www.tinkercad.com/things/9HEOkFHbj68 Print Settings Printer...

Nice stylus table stand to focus on working digital and this way only have a tablet stylus on your desk! ...It can hold any stylus with a diameter of 8mm.

Please refer to the original for printing instructions and where to find the jets. ...All that information is applicable to this remix

This is a simple Desk Stand for the Geekvape Wenax Stylus vaping device.

... work with pretty much any pen that's less than 10mm in diameter. If you like this check out some other Stylus designs: Stylus USB holder https://www.thingiverse.com/thing:2766368 Stylus Pen Pocket Clip https://www.thingiverse.com/thing:2803698

Case for PocketCHIP. ...The stylus is on the left hand side for a speaker can be added on the right. Along with this there are speaker holes. ... Files are in mm.

Hi Guys This stand designed for Wacom Intuos Creative Stylus (But you can use similar Wacom Stlyus) If you want to get the best Printing results; Support angle Min. 50 Degree. Dense 3 Layers. Space 8 Layers. Print with Raft. ... And Get...

Case has a low profile and larger stylus than other cases made. The battery is exposed to decrease print time. ... Files are in mm.

7mm Tablet Stand + Stylus Holder

A simple stand for boox triangular pen

This is a simple phone stand, designed to keep the phone steady for writing with a stylus at a 30-degree angle. It is large enough to fit any phone. There is a groove on the bottom, so if you want to prevent it from sliding, you can fill it with hot...

A cutout in the bottom of the holder allows you to have the USB or phono jack connected while in the stand (needs to be tilted slightly when a cable is used). There is also a holder for a stylus, used to control the touchscreen. There are 3 files:...

... for Fire 7, thou might be scale-able for other types. (Teamviewer app on Fire Tab remote viewing into a windows 10 pc running Sketchup XD) Stylus used: https://www.amazon.com/gp/product/B07GF8FQRK/ref=ppx_yo_dt_b_asin_title_o01_s00?ie=UTF8&psc=1

This file is meant to attach to the telescoping pole stand that one can hand most Rotary tools from.

Stand to reduce table clutter when not using Wacom tablet.Made for my Intuos Medium (PTH-651) but should work with others.&nbsp;Category: Computer

Stand to reduce table clutter when not using Wacom tablet. Made for my Intuos Medium (PTH-651) but should work with others. ...Print Settings Printer: BCN3D Sigma ...

Version 2 (Home-Button) 7mm Tablet Stand + Stylus Holder Version1: https://www.thingiverse.com/thing:3244699

Replacement back for PocketCHIP computer. ...The case has an integrated Stylus and Kickstand. ... Files are in mm.

Thx 4 attension

Replacement back for PocketCHIP computer. ...The case has an integrated Stylus, Kickstand and the battery is protected. ... Files are in mm