super73 headlight 3d models
3647 3d models found related to super73 headlight.
thingiverse
My Video of my Mod: https://www.youtube.com/watch?v=xzKf4IqEQXo 30% infill Cubic
thingiverse
This is a bracket to mount a Mictuning LED headlight to a Super73 air suspension fork (bolts on to the underside of the crown)
thingiverse
Bicycle battery mount for Kanebilt's Super73 R headlight kit. ... Directions: Print 2 parts Clean up parts to ensure clean fit Epoxy two half's of case together Use hair ties or rubber bands to secure battery Install to bike with 2x M5 screws Headlight...
thingiverse
Super73 logo because im that much of a fan. Used the cura "extra fine" settings for the smaller one and "draft" for the large. ... Printed in PLA
thingiverse
Because I'm a fan of Super73 I decided to make myself a keychain that I will use for the battery key on my bike. It turns out looking great. you may want lightly sand, put primer and spray paint to make it look perfect if you are picky. ...
thingiverse
Some simple spacers to raise the stock seat of the Super73. For the long seat version I used two "Ts" and two straight spacers for the cargo rack. ... Updated the single spacer.
cults3d
3D printable aero wheel covers for the Super73 wheel. Use double sided 0.5inch width tape to adhere the wheel cover on the rim. ... I recommend this tape: https://www.mcmaster.com/75935A111/ Use superglue to bond the plastics together if you are not...
thingiverse
Use this to mount the Super73 S1, SG battery undeneath the frame. You will need. 2 x M5 x 16 or 20mm (you might be able to use 2 of the original bolts!! I cant remember!) 1x M5 x32mm i used and 8pin 400mm extention cable to relieve stress on...
thingiverse
Super73 front light bracket You will need a 10mm longer bolt
thingiverse
Endplug for super73 handlebar. ... Need to be upscaled though, had to use some tape to fix the first.
thingiverse
This is an experiment with designing a molle panel for the Super73 ZX. ...In my testing its not strong enough to hold anything heavy so high infill or squishing the whole thing thicker may be needed.
thingiverse
This is a sleeve to turn your thumb throttle into a twist throttle for a Super 73 S1
thingiverse
Gopro adaptor mount for a rear view screen for the Super73 RX
thingiverse
Since the Super73 ZX doesn't come with any fenders or splash guards, I made one. I modeled it after an RX but should fit on any model of bike. I also added my Fusion360 model if you want to remix it. ...Let me know if it works for you!
thingiverse
My Video of my Mod: https://www.youtube.com/watch?v=xzKf4IqEQXo 30% infill Cubic
thingiverse
My Video of my Mod: https://www.youtube.com/watch?v=R9VQ8obho3Y My video of the Light Mod: https://www.youtube.com/watch?v=xzKf4IqEQXo Allign the text and the plate in cura. Print the text first and after the plate. ... For the plate i used: ...
thingiverse
I've yet to buy (or print?) fenders for my ZX, and found that minor puddles and sploshes wet both my bum and the very sensitive control unit under the seat. Now, I'm sure the connectors and enclosure were designed to get a bit damp, but I wanted to...
thingiverse
Super73 chain guard, straight bolt on, no need to remove anything....apart from the original chain guard!! :-) Fit S1/SG pre 2020. Please check the chain ring in the pics is the same. ... This will not fit the new version.