supermicro 2 5 to 3 5 3d models
2843143 3d models found related to supermicro 2 5 to 3 5.thingiverse
This is a 2.5" to 3.5" hard drive adapter designed for use with Supermicro drive carriers. Screw holes all in correct location and size. Drives slide right into the backplane no issue :D Prints without supports at the layer height of your...
thingiverse
In my caddies there are holes for 2.5" drives already on one side and I had to remove the plastic from thing 36610 on that side to make it fit correctly. You probably need to run a drill through the holes to make them correct size. Now it's also...
thingiverse
... didn't fit my method of construction. ...Two of the holes were also off by 1mm (ones closest to the breathing hole of the hotswap tray). I added witness holes for easier mounting of the side screws. ...Bridge should be fairly easy to print on 0.2mm.
prusaprinters
This is airflow optimized SSD mount in the 3,5" Supermicro drive sleads. This is based the OEM MCP-220-00043-0N mount and works with 7mm thick SSD, let me know i you need a diffrent size. This is made to balance airflow over the spinning rust (HDD)...
thingiverse
This is a 3.5" to 2.5" adapter for some Supermicro servers. Specifically, it replaces the bracket in Supermicro part number MCP-220-00043-0N. In other words, printing this allows you to use a 2.5" drive in your current 3.5" drive tray. Note that...
thingiverse
Adapter is capable to keep and mount standart SATA SSD to hot-swap tray 3.5" in Supermicro Servers. Tested. Working. SSD targeted to SATA-Socket, thats ok. ...May be need to increase some holes by drill.
thingiverse
Option without using nuts. ...Just holes where standard screws are screwed in.
thingiverse
Printing this allows you to use a 2.5" drive in your current 3.5" drive tray. Note that 3.5-2.5 adapters usually place the small drive in the middle of the 3.5, thus it does not fit into the hot-swap slot. This project is modified/optimized for...
thingiverse
Simple adapter for mounting 2x 3.5" SSD disks into 3.5" HDD caddy, in this case I used it to mount SSD's into Supermicro 2U case and his top "open slots for optional hard disk drives"
thingiverse
Very simple Supermicro Server Caddy / Tray for 3.5" Harddisk. ... SuperWorkstation 7046A-3 SYS-7046A-3 4U compatible
thingiverse
This tray is designed to hold two 2.5" internal drives within a Supermicro 846 chassis. This tray mounts to the existing stock mounting points used for the OEM accessory tray made by Supermicro. ... The included tray offset bushings are intended to be...
thingiverse
SSD 2.5 to 3.5 Mount Good for traditional HDD bays - Requires 4 m2.5 screws
thingiverse
3.5 inch caddy for 2.5 inch drive. ...Has top and bottom part to make a full size 3.5" hot swap drive.
thingiverse
Hard drive adapter made to fit a 2.5" SSD into a 3.5" tray. ... Holes on the sides match standard 3.5" drive mounting holes.
thingiverse
A simple and fast to print adapter, to fit a 2.5" HDD/SSD drive into a 3.5" slot.
thingiverse
This is a Adaptor for a 2,5 inch ssd to 3,5 inch hdd. Test with 2,5 inch Intenso SSD OK! ... Use on your own risk!
prusaprinters
SSD Drive Adaptor 2.5" to 3.5"This is a remix of: https://www.thingiverse.com/thing:3094581
thingiverse
This is a little bracket for mounting 2.5" drives in 3.5" places. ...
youmagine
This is SSD or 2,5' hdd drive adapter to fit 3,5' bracket in PowerMac. It enhance 2,5' drive bottom holes to fit 3,5' drive bottom holes. For 2,5' drive I choose DIN 965 -> cross recessed countersunk head screws. 3,5, standard flat screws. One...
prusaprinters
This adapter allows to put a 2.5 drive in a 3.5 bay keeping the connector in the same place.Dimensions and screw holes are exact taken from drives specifications.Useful if you have a server caddy.Model is upside down for printability without...
cults3d
2.5" SSD hard disk adapter for 3.5" bay mounting (HDD IDE/SATA bay) It can also be mounted in the 3.5" floppy disk bay.
prusaprinters
SSD or HDD adapter from 3.5" to 2.5" drive.You are going to need 4 countersunk screw M3x6mm for mounting drive to the 3D print
thingiverse
HDD adapter 2.5 to 3.5 printed from PETG on my Prusa MK2 Clone - check my printing and assembling video: https://youtu.be/-gThpA9R60E - dont forget check my youtube channel: https://www.youtube.com/channel/UC1TvQhLswn7xaqo4nip_7Bg