supermicro 2.5 3d models
1212792 3d models found related to supermicro 2.5.thingiverse
This is a 2.5" to 3.5" hard drive adapter designed for use with Supermicro drive carriers. Screw holes all in correct location and size. Drives slide right into the backplane no issue :D Prints without supports at the layer height of your...
thingiverse
In my caddies there are holes for 2.5" drives already on one side and I had to remove the plastic from thing 36610 on that side to make it fit correctly. You probably need to run a drill through the holes to make them correct size. Now it's also...
thingiverse
This tray is designed to hold two 2.5" internal drives within a Supermicro 846 chassis. This tray mounts to the existing stock mounting points used for the OEM accessory tray made by Supermicro. ... The included tray offset bushings are intended to be...
thingiverse
https://www.thingiverse.com/thing:4353094 had a good idea but didn't fit my method of construction. Two of the holes were also off by 1mm (ones closest to the breathing hole of the hotswap tray). I added witness holes for easier mounting of the...
prusaprinters
This is airflow optimized SSD mount in the 3,5" Supermicro drive sleads. This is based the OEM MCP-220-00043-0N mount and works with 7mm thick SSD, let me know i you need a diffrent size. This is made to balance airflow over the spinning rust (HDD)...
thingiverse
The Supermicro 815 1U case 2.5" HDD and BBU holder as seen on https://www.wanhunglo.com/2022/supermicro-815-1u-case-25-hdd-and-raid-card-battery-holder-p40 If you can, please use the RSDOC (RS DesignSpark 5) file as that's my original source file. ...
thingiverse
... for an SSD. The SSD is not supported on the bottom edge, but since it's so lightweight and it won't be moving around, it should be fine hanging there. The mount points need 2 standard #6-32 screws (same as 3.5" HDD), and the SSD needs 2 M3 screws.
thingiverse
I bought a SuperMicro 6028U-TRTP+ 2U server and needed to install a 2.5" ssd. This chassis has an option for a dual 2.5" internal bay, but mine didn't come with one. So I designed and printed my own. I couldn't find a good place to buy a SuperMicro...
thingiverse
Building on the reinforced SSD mount i wanted something that could hold my 10K 2.5" disks as well as a few SSDs. This prints in two parts, one for the top and one for the bottom. It is being secured to the PSU wall with the screws that came with the...
thingiverse
I build a caddy / tray based on the original HDD MCP-220-00001 drive tray and made it to be printed out fast and (nearly) without support (See: https://www.thingiverse.com/thing:4137086 ) However, you can't use 2,5 inch drives or SATA SSDs with the...
prusaprinters
It is stable enough and you can use standard 2,5" harddisk/ssd screws. Only as a second option I also made a screws-only versions, which requires the small supermicro screws.This "supermicro-caddy sff with screws v3" version doesn't need any support....
thingiverse
This is a 3.5" to 2.5" adapter for some Supermicro servers. Specifically, it replaces the bracket in Supermicro part number MCP-220-00043-0N. In other words, printing this allows you to use a 2.5" drive in your current 3.5" drive tray. Note that...
thingiverse
Simple adapter for mounting 2x 3.5" SSD disks into 3.5" HDD caddy, in this case I used it to mount SSD's into Supermicro 2U case and his top "open slots for optional hard disk drives"
thingiverse
no materials needed (only four screws that you got for the new 2.5 drive and two of the four old 3.5 drive screws) - the hex nuts are not needed, they are replaced with the idea of repurposing the standard screws 5. ...ability to hold HDD/SSD in place...
thingiverse
Reinforced the mounting mechanism to allow the printed piece to be pushed onto the 7,5mm studs on the PSU-wall. Uses the factory screws that came with the chassi to be used with those holes. I used supports on the holes that pushes on the studs.
thingiverse
Adapter is capable to keep and mount standart SATA SSD to hot-swap tray 3.5" in Supermicro Servers. Tested. Working. SSD targeted to SATA-Socket, thats ok. ...May be need to increase some holes by drill.
thingiverse
Either as one solid piece that bolts directly to the PSU-wall or as a 2-piece version that bolts together with the reinforced SSD Mount (https://www.thingiverse.com/thing:4771178) using 2x M3 nuts and screws. These only fit slim SSDs and slim...
thingiverse
Option without using nuts. ...Just holes where standard screws are screwed in.
thingiverse
Very simple Supermicro Server Caddy / Tray for 3.5" Harddisk. ... SuperWorkstation 7046A-3 SYS-7046A-3 4U compatible
thingiverse
Fairly easy print, worked on multiple resolutions without much cleanup. Keep support minimal for easy removal. Side rails glue onto front piece, and by having them print flat, they print much faster. If anyone wants a model with the rails...
thingiverse
I acquired a used server mainboard by Supermicro which came with a front panel PCB which is only compatible with Supermicro server cases. I designed a faceplate for this PCB which is compatible with a 3.5 inch bay of my CS 601 case. It should fit in...
thingiverse
For the famous (and nowaday super cheap second hand) Supermicro CSE-815 1U server chassis, I designed a harddisk caddy (hard drive tray) for 3,5 SATA/SAS HDDs. I liked the idea of https://www.thingiverse.com/thing:2413043 , but build these on my...
prusaprinters
For the famous (and nowaday super cheap second hand) Supermicro CSE-815 1U server chassis, I designed a harddisk caddy (hard drive tray) for 3,5 SATA/SAS HDDs. I liked the idea of https://www.thingiverse.com/thing:2413043 , but build these on my own,...
thingiverse
... partage de mon installation pour Supermicro cse 846. ... Adaptateur 2 x 120mm a fixer avec les 3 vis d'origine, les attaches en crochet peuvent casser mais ca ne gene en rien la fixation ( aucune vibration ). Voila si ça peut vous aidez. ...:)
grabcad
Heat Sink Supermicro SNK-P0057PS Radiator.Accurate up to 0.05mmStep 214 and parasolid v28 attached.
thingiverse
Adapter to allow for 40x40x20mm depth fans to be mounted into Supermicro E200 server with 28mm depth mountings.
thingiverse
This hot-swap drive tray fits the Supermicro SC743 chassis, and is a replacement for part MCP-220-00092-0B. ...