supernight led driver 3d models
92394 3d models found related to supernight led driver.thingiverse
Supernight LED Driver Cover. This part fits the end of the PSU to protect the connections. ...I moved the holes to the right side, to get out of the way of the 120v power cable that plugs into the IEC Socket.
pinshape
Supernight LED Driver Cover. This part fits the end of the PSU to protect the connections. ...I moved the holes to the right side, to get out of the way of the 120v power cable that plugs into the IEC Socket.
thingiverse
This cover is designed with a integrated power switch/ outlet.http://www.amazon.com/Inlet-Power-Socket-Switch-IEC320/dp/B00511QVVK
grabcad
Constant Current LED Driver Powers four 1W or two 3W LED's. High efficency Switch Mode operation. Driven from 6-14v AC or 9-18v DC source. 350mA or 700mA configurations. ... For detailed build instructions and parts list go to:...
thingiverse
This is by far the easiest and cheapest mounting option for the Supernight I have tried. Once printed, line up the Bottom portion to ensure it is straight, and make three mount holes in the frame with a pencil. Drill out the three holes to accept M3...
grabcad
A selectable led flash light driver. ... Part: http://illuminationsupply.com/8xamc7135-28a-selectable-mode-driver-p-45.html
thingiverse
Mini LED driver holder. Driver used to control 3d printer lights. ... Driver from http://goo.gl/Onm0Nk used with lights http://www.thingiverse.com/thing:856626
thingiverse
A simple case to go over my Picobuck LED driver and protect the contacts. Note that it has ventilation holes, but they might not allow enough cooling, depending on how you use the driver. ...Also, I only used one output of the Picobuck, so I only made...
thingiverse
I like these tiny LED drivers on Ebay, but the box was a little bit too big. So I designed a smaller box. ... Printed in PETG 235 nozzle, 70 bed, 0.2 layer, 25% infill
cults3d
I like these tiny LED drivers on Ebay, but the box was a little bit too big. So I designed a smaller box. ... Printed in PETG 235 nozzle, 70 bed, 0.2 layer, 25% infill
thingiverse
This is designed for a standard 12v LED driver module and has suitable outlets for power and two separate lights and two switches on the top plate. ...A link to the required...
thingiverse
Based on the driver for ME 2019 LED Strip Light Kit, New Acrylic Back Tape, 16.4ft Water-Resistant Flexible Multicolor 5050 RGB Lighting; however, it should work for other products with the same driver. See installation details below. Requires a...
myminifactory
This is a follow up part for the adjustable LED base: https://www.myminifactory.com/object/50232 If you have your LED’s and the right resistor (I have talked about in https://www.myminifactory.com/object/50232) you can make this driver case. I...
thingiverse
If you have your LED’s and the right resistor (I have talked about in https://www.thingiverse.com/thing:2660485) you can make this driver case. I included a schematic for connecting the parts. Because it’s so simple, I didn’t even make a PCB, but...
pinshape
If the range does not work for you because the LED is already at max level when the potentiometer shaft is only at 50%, than you can replace this resistor with a 50K potentiometer to “fine tune” it. Than you need a case to hold the parts...
cults3d
If you have your LED’s and the right resistor (I have talked about in https://cults3d.com/en/3d-model/tool/adjustable-led-base) you can make this driver case. I included a schematic for connecting the parts. Because it’s so simple, I didn’t even make...
thingiverse
Ok guys, the LED driver of the chinese LED ceiling lamp I bought was way too big for the small circuit board, and I needed space to fit in additional stuff (Wifi control module, etc.), so I set out to design & build a smaller one. So there you go,...
prusaprinters
Do not print and install this model if you don't know what you're doing!!!This model is a replacement enclosure for a 24V LED driver with passive cooling. ...You can mount the power supply to the enclosure with some M4 bolts and...