sure electronics 3d models
141695 3d models found related to sure electronics.thingiverse
Needed a case for the Sure Electronics AA-AB32261 pre-amp. Has holes for RCA jacks and a cable hole on the opposite side, as well as a hole for the DC plug. No vents. Should have taken a photo but now it is buried deep within my car... ...Print Settings...
thingiverse
A mount for Sure Electronics AA-AB32174 2x50W TDA7492 Class-D Amplifier Board.
thingiverse
... front of the case. Put a 30cm wire to extend the wireless signal of the bluetooth (now 30m instead of 10m). Module can be ordered here : http://store3.sure-electronics.com/audio/wireless-and-cable-audio-signal-transceiver/bluetooth-receiver-board
thingiverse
Enclosure for SURE electronics AA-AB32231 2 x 8W audio amplifier board with class-D architecture and integrated TPA3110D2 chip Print Settings Printer: Renkforce RF100 Rafts: No Supports: No Resolution: Low Notes: 8mm skirt How I Designed This Used...
thingiverse
The thing image is from their product webpage: https://www.parts-express.com/sure-electronics-aa-ab32313-2x400w-class-d-audio-amplifier-board-compact-t-amp--320-3368 I made this design to help me plan and layout an amplifier project. ... Drawn with...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1264391 Instructions Using the following options: TxtSize = 3 txt = SURE CLASS D AMP 2x 100W @ 8 ohm Length = 145 Round = 6.1 Resolution = 50 TShell = 1 Height = 60 Width = 110 Thick = 3 m = 0.6...
thingiverse
Housing for Sure Electronics / Wondom DSP and RCA interface. Created with SketchUp. Holes for mounting on a surface are located on the base plate. Additional screws are required: M2.5 35mm. The housing also works for the Sure DSP without the...
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
thingiverse
Customized version of https://www.thingiverse.com/thing:3078260 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3078260
thingiverse
Customized version of https://www.thingiverse.com/thing:3516901 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=3516901
cults3d
... the Sure Sucker will do the trick. ...The Sure Sucker is a mouth ring gag designed with strap connectors and is ribbed to increase sensation for your lover. You can attach straps to ensure a certain fit. ...It is recommended to be printed in rubber.
thingiverse
... one where the darts face opposite directions. If you use this, make sure that you have good spring tension for the mag holding latch. The extra weight can cause the mag to fall out and damage the bottom mag. Ask me how I know this. ... :-)
thingiverse
... of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: font_scale = 1.6 word = Sure You Can pen_length = 130 font_spacing = 0.81
thingiverse
... of http://www.thingiverse.com/thing:45576 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=45576 Instructions Using the following options: word = Sure You Can font_scale = 1.65 font_spacing = 0.8 pen_length = 130
thingiverse
# Sure Garden ## Properties - Modeling in FreeCAD ## Images ![Photo 1](https://gitlab.com/3d-land/3D-Printing/-/raw/master/huerta/huerta1.jpeg) ![Photo 2](https://gitlab.com/3d-land/3D-Printing/-/raw/master/huerta/huerta2.png) ## License [Creative...
thingiverse
Made a quick simple wrench for "sure Shot" brake clean sprayers, 15/16" I leave a few by the barrel for the shop to use, 8/7/21 added a press on handle that someone at the shop requested I've tried several times to add pictures of the ones i have...
thingiverse
I made up this spanner set for the Milwaukee Sure shot sprayer https://www.sureshotsprayer.com/SteelSprayers.html There is a spanner for the filler plug as well as both parts of the nozzle. I guess if I was going to print them again, I would make the...
thingiverse
Sure it's harder that you think ! Ce cube, nommé "blackbox" comme l'outil utilisé par les physiciens dans la recherche nucléeaire... (une particule entre, va-t-elle sortir mais où ?) est imprimé à une taille de 10 cm de côté. En placant une bille...
thingiverse
This is an amplifier enclosure intended for the Dayton DSPB / KAB series of Class D amplifiers also sold under the brand Sure Electronics Wondom. It takes two of the boards so it can create 3 or 4 channel amplifier perfect for a stereo set of...
thingiverse
Needed a way to play with these amps on my desk and protect them from shorts. ...The double holds a sure 300w power supply and a 2x100w amplifier. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/iOQSpJkb0jS