switch mount for pro controller 3d models

This custom mount is engineered specifically to integrate seamlessly with a particular GoPro mount found on Thingiverse, where it can be downloaded and 3D printed.

Version Two of the GoPro mount has been modified by splitting it into two parts, allowing for easy clamping down on the rubber damping balls and preventing them from popping out of their holes. To secure this design, I used two M5 8mm bolts with...

... So I remixed the design a bit and enlarged the surface between the wheel and the mount. I also added a "evolution kit", that you can clue to the original design, so did I and it works better now. There is also a new design including this changes.

After watching the CR-6 announcements and noticing its filament spool holder, I had an idea for a unique way to mount a camera. The video at https://www.youtube.com/watch?v=phYjh2Rwrqk caught my attention, showcasing a simple clip-on design that...

Made based on Ep3d's mount, offers same clean look, but instead of screwing in you just rest the Pad on convinient slides for built-in legs of the Sonic PadAlso OG felt like using a bit too much of filament so also tried reducing it by adding some...

So I remixed the design a bit and enlarged the surface between the wheel and the mount. I also added a "evolution kit", that you can clue to the original design, so did I and it works better now. There is also a new design including this...

Are you tired of your thermostat constantly falling to the ground? ...This is exactly where the Thermos Control Pro 2 Wall Mount comes in, providing a simple and effective solution for your problem.

Following the great work by FortinMike in modifying the original Koss PortaPro/KCS75 Adapters for the Oculus Quest https://www.thingiverse.com/thing:4822413 and the remix by Thorlian https://www.thingiverse.com/thing:5222313, I have created an...

... able to salvage the pin and camera in one piece. For now, I'm just utilizing the pivot pin from the cam but would prefer to obtain a nut and bolt for it to secure it tightly.\r\n\r\nI also intend to reconfigure the hole for the USB cable as well.

An updated face tracker mount, fixed topology to play nicer with slicers and reinforced

this is a model made to mount you favourite action cam on top of the olight rn 400 bike flashlight.to install it, unscrew the out of the box mount of the flashlight, slide the flashlight inside of the new mount and screw back the bike mount.

This is a remix of Denis Cheongs mount https://www.thingiverse.com/thing:4181248

Edit with horizontal cable mount as requested by Jason118

The higher the infill the sturdier the mount. ...I recommend 30%.

... are taken out of two A4 files and works perfectly. Knobs on the back of the microphone are accesible, but its not comfortable to tweek them in the mount. BOM: 1. Ikea lamp 2. 2x M3x10 screw 3. 2 stretchy cords from A4 file 4. ...Filament

I engineered a hybrid camera mount by combining an innovative rail adapter with a U30/LK4 installation system. To address the weight of my camera, which was indeed substantial, I designed an optional support leg to provide additional stability. The...

And added 3rd mounting brace for stability. Also there is nut and bolt included for installiation of blowers. Blower can be found in original design. I am using it with 24V 60mm fan. It was still noisy and I used 180ohm / 3w resistor in serries....

See also my dual DyzEnd mount: https://www.thingiverse.com/thing:4699580 Updated for the Ender 5, which has a wide carriage plate that isn't compatible with the previous design, as well as requiring a different mount for the part cooling fan. The...

This is the extruder I use in my flsun qqs pro that i convert to klipper and uses SKR PICO.I relocate the extruder location to the bottom of the printer to reduce the weight at the top, so it does not wobble as much.

DONATE: https://paypal.me/RinboLab?locale.x=it_IT Printed with Alfawise U30 Pro with PLA+ filament from Sunlu. Layer height: 0.2 mm Walls: 2.5 mm Filling density: 17%. ... Flowrate fill: 95% Extruder temperature: 202°C Printing speed: 60 mm/s

... the vista. ...It fits in the reces of the FPV canopy of the AR wing Pro. also secure the canopy in some way, else you will lose it! its operatred with a normal 9g servo. ... the Clamp part goes on the inside of the canopy and holds the M3 nuts.

Ich wollte mein altes MacBook Pro unter dem Schreibtisch lagern und habe leider nichts passendes dazu im Internet gefunden. So habe ich selber etwas entworfen. Es würde mich freuen, wenn ihr auch damit etwas anfangen könnt. Bei mir klappt es damit...

Depending on the material, reduce the scale (down to 97%) I used TPU A93, and scale 97%. ...It fits tight as it should. It weighs around 2.5 gramms. I've printed it on my Ender 3 Pro with stock bowden.

Improved mount for the Z axis motors on my CTC I3 printer. You can use a M8 rod to connect these mounts with the M10 Y-Axis rods. The Motormount STL file is for both left and right motors. Use M10 Nuts and big washers to get a really strong...

My Custom Hemera Mount: A 90° Rotation for Balanced Printing I've taken the liberty of designing my own hemera mount, carefully rotating it by 90 degrees to perfectly complement the gantry of my BLV ender 3 mod. This thoughtful adjustment ensures...

I modified the Y-axis front mount to be the maximum width and exact length to prevent the clamp from having the ability to shift in any direction. ...This mount is very rigid now.

... this integrated GoPro mount. To achieve this, I modified a GoPro buckle mount created by PVL, which I discovered on Thingiverse (Check out theirs below). ... GoPro Buckle Mount by PVL Published on January 28, 2016 www.thingiverse.com/thing:1299803

I've made a very slight remix of RedAngel1984 Fan Mount. ...It's just the mount object itself. As you can see in the photo, the black one is the original - all I've done is modify the mount holes to accommodate Geeetech black screws perfectly.

This part uses the pieces from the original camera mount, specifically the hinge pin and screw and the two little sticky end covers if you want, so don't throw these away when you take the camera mount off. The hinge pin will push through the new...

... ... Print Settings: Printer: Flashforge Pro Rafts: Yes Supports: No Resolution: Medium Infill: 25% Post-Printing: The updated design requires attention to its orientation during the print process; once correctly positioned, no support is necessary.