switch mount for traxxas 3d models

I've designed a custom 3D printed switch mount for my Traxxas Slash 4x4 HCG, specifically to house the brushless motor system's switch. Since it needs to be installed somewhere, I'm providing this file with installation details. To download and...

To Mount Your Hobbywing Max5/Max6 Switch Differently, First Get Two M3 Screws That Are Either 6mm or 8mm Long. ...You'll Also Need Two #8 Washers, Which Can Be Small as Long as They Combine to Be More Than 8mm Wide.

Mounting the switch to your Traxxas X-Maxx is a breeze using this method with the Hobbywing Max6 ESC. Simply remove the existing screws from the wire holder, then swap them out for slightly longer ones. The new switch will snap securely into place in...

Hobbywing ESC power switch mount for Traxxas Maxx. Printed in PETG for strength and high temperature resistance. ...Requires two M3 by 10mm screws to mount to existing holes in chassis brace.

This is to securely mount the Hobbywing Max8 power switch to the center chassis brace on the traxxas Maxx

The driver firmly grasps the Electronic Speed Control (ESC) power switch of the high-performance Traxxas E-Revo Brushless Edition, a cutting-edge off-road vehicle designed for extreme racing and stunt driving.

Printable Traxxas OBA mount for UDR can be adapted for use in other models. The design makes use of original M3 mounting screws to secure it firmly beneath the cabin carcass, utilizing flat areas on both the pilot and copilot sides. ... To ensure...

You will need an m5 nut(non-locking) and an m5 bolt although one is included in the stock mounting hardware for the GoPro Place the smaller part's base in hot water for a few minutes before placing it into the hole and you should get a perfect fit...

Hobbywing MAX6 mount for Traxxas XRT

This is a Traxxas Telemetry Expander 2.0 mount, for mounting on the T-Bar of the Traxxas Sledge.

It also has a mount for the switch. The lower plate is held to the chassis with either 2 or 3 M3 x 8 flathead screws, and the upper bracket is held to the lower base with 4 M2.5 x 22mm buttonhead screws with 4 M2.5 thin nuts. The nuts can be glued...

It also has a mount for the switch. The lower plate is held to the chassis with either 2 or 3 M3 x 8 flathead screws, and the upper bracket is held to the lower base with 4 M2.5 x 22mm buttonhead screws with 4 M2.5 thin nuts. The nuts can be glued...

Hobbywing max8 G2 mount for Traxxas Maxx. This is just a copy of the Hobbywing mount with the holes offset so the esc mounts in the original location. Edit: mounting holes moved slightly, hopefully will be easier to mount. ...

Mix of two files with endplate to avoide that the switch moves out. ...(picture is without retaining plate and not yet tested if it fits!)

This is a mount to connect the Castle Sidewinder ESC to the Velineon mounting holes found on Traxxas RC cars. It prints flawlessly with support material and a slight sanding if its a snug fit. You will need new screws - M3 (US #10) screws that are...

... was a good buy but didn't come with any mounting hardware. This is an ESC mounting bracket which mounts on the stock mounting posts. Compliant tabs hold the ESC in place and allow for easy removal. No overhangs. ...Easy to print.

This GoPro camera mount clips on the rollbar of the Traxxas XMAXX. ...It is offset so that the camera lens will be centered over the roof top. This mount also has provisions for 4 zip-ties to better secure it to the rollbar.

Mount created to enable use of Traxxas rods with the Duet3D smart effector for delta printers. I have been pleased with my Traxxas rods, and wanted to try them on the new effector before considering magnetic arms. It appears to be stiff enough and...

This is a fan mount for 40mm fans which fits on original Traxxas chassis braces. The screw holes on the brace side are 3mm. Holes for the fan can be easily drilled into the filament, after marking the positions of the holes of the individual fan.

Designed in AutoCAD, this allows for dual motors on a Traxxas Slash 4x4. This been tested in ABS and I've printed them on a Tevo Tornado 3D printer. ...Some filing may be required for perfect fit.

Print it flat on the back side and bolt it together with 2-M4 x 25 screws and nuts at the bottom, 2-M4 x 12, screws at the top, and 2 M3 x 10 screws (M3 x 15 for the flat top version) through the mount and into the top of the shock tower. The...

Since I couldn't find a phone mount for my Traxxas TQi remote, I made this instead. This design only works with iPhone 8+ (possibly not 6+ or 7+ due to mount thickness), as I don't have those phones to test it with. This model may contain some...

However, this proved difficult, so I designed the body mount spacers to address the problem, making the stock body mounts adjustable in the process. To download the bottom mount spacers, you'll need screws that are at least 3x20mm or longer,...

The original plate allows the ESC to be mounted into a Traxxas car like a Slash, Rustler, etc.  This plate serves exactly the same function but it is slightly thicker and stronger to help prevent the cracking that sometimes occurs on the...

I designed a straightforward mounting adapter for a 21mm x 15mm switch, specifically to integrate a switch into my workbench LED lighting system. ...The switch clicks securely into place within the adapter, which then slides effortlessly into a 1-inch...

This is the crossbar that holds the body posts on an ancient Traxxas Sledgehammer. I think it should be at its strongest when printed on its side, as is. I used ABS and it's holding together so far. ... Category: R/C Vehicles

very simple 1080 mount for the trx4, places the esc as much inward as possible. ... i used hot glue to put esc on the mount

I mounted my body mount on the front side of the shock tower, so make sure to factor that in when building yours - this may or may not work for you. P.S. ...If you need these printed out for yourself or if you're into RC stuff then check out my...

This is a mount for a gopro baseplate. Print and use the dummy before, to mark the exact cut-out. The mount will be fixed with 2 M3x12mm countersunk screws on the inside of the roll cage. After assembly, screw the base plate with 3 M4x16mm...

This will perfectly fit over your ESC and bolt securely onto your car using the original VXL mounting holes.