syma drone 3d models

Syma drone battery/charge storage.. I can always find 1 or2 then think where is the others. ...I put SYMA on the side because  I am new to design and discovered it by mistake , I meant to number them so I could use in sequence

This was designed for the Z4W but there are a number of Syma drones that use this same exact controller that this will work for. I Printed this in pieces to make printing it much easier. You could place this on your slicer such that your...

This was designed for the Z4W but there are a number of Syma drones that use this same exact controller that this will work for. I Printed this in pieces to make printing it much easier. You could place this on your slicer such that your printer...

SYMA X8SW-D drone blade/bump guard, fits into the stock hole without a clip and stays in during flight pretty well, haven't lost one during regular flight , only when I smacked a tree really hard it came out after protecting the blade. ... They are not...

Famous syma drone conversion to drone racing and change MOTOR 8.5mm dianetre!!!

Famous syma drone conversion to drone racing and change MOTOR 8.5mm dianetre!!!

This is a cover for charger for SYMA drone. The charger covers should be glued. I used adhesive glue. Adjust the covers using a small triangular file. ...Particular attention should be paid to the USB port.

Frame for all X5 syma drone parts. Only 10 grams. To easy for install parts no need any skill. ...All wire go inside of frame.

Frame for all X5 syma drone parts. Only 10 grams. To easy for install parts no need any skill. All wire go inside of frame. Use supports only for top (not for tunnels) PLA, ABS, PETG 5-20% infill, 1-2 wall (0.40-0.80), 2-4 layers top-bottom 0.200...

So I had a number of these extra Syma X8 motor housings (http://amzn.to/2l50c4k) laying around so I decided to design a 3D printable adapter to use them on a quad build project! You can also get the reciver here (http://amzn.to/2lgVFY3) to drive the...

With that in mind I recreated the design from scratch to fit smaller rotors, 7mm motors and also has the particular flight controller mount that fits the Syma board. The ducts are a close fit for the 37.5mm propellers and curved to a NACA 0020...

This design is created using Fusion 360 Generative Design. ...It was meant as a landing structure..

Customized version of http://www.thingiverse.com/thing:551484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=551484

SYMA X25 GO-PRO holder that is flight tested and 3D printable

Customized version of http://www.thingiverse.com/thing:551484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=551484

Customized version of http://www.thingiverse.com/thing:551484 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=551484

Supported models: SYMA X8SW/X8SC/X8PRO/X8S-03Original legs are universal, but because i had to rotate the pods in relative to the base of the legs, left and right versions are inevitable.I reccomended to use PETG or 98A TPU as a printing material,...

Want your Syma (or Syma clone) quadcopter to be faster and more responsive? Remove the stock landing gear and replace it with these little feet. They hold the quadcopter just off the ground when landing or taking off, and they greatly reduce air drag...

drone designed for the components of the syma x5c drone If you found this useful, please donate what you think it is worth to paypal.me/kylianbarre. Help cover the time of design. Thanks, Enjoy! ...

Customizable leg for Syma X8 drones.

Drone de ma conception, reprenant les éléments mécaniques et électroniques d'un drone syma x5c (24€ sur banggood) Il faut uniquement dessouder puis ressouder les fils d'alimentation des moteurs pour les passer dans les bras. Les assemblages sont...

This is a loop hook for a carbiner for use with a syma drone. This was designed by blender which is a free 3d software. ... www.blender.org

This is perfectly suitable body for Syma drones like x5sw,x5se etc. ... Printer settings Temperature of nozzle is 220° and bed temperature 50° No support required Infill 15-20% Parameter 1 Layer height.0.3 Resolution 0.2-0.4 The placing of Syma receiver...

This is a project that I started a while ago to convert my broken Syma toy drone into a fast racing-style drone. Arm extension and support for my hollow framed-drone with Lumenier motor. The toy-grade Syma X5C-1 has a 2400mm x-style frame. After...

And I wanted to replace the stock lamp cover on my Syma d360 drone because I replace the stock led lights that came with the d360 Drone because I wanted to add front and rear lights on my d360 drone and as a result I ran into some problems with the...

Tapa engranajes Syma X5 sc Drone La he buscado por muchos sitios y no he encontrado donde comprarla. Lo primero que se perdio en mi drone. Primera pieza que subo :) Diseño NUCLEAR, no las típicas aspas... Pesa menos de 1gr. Enganche reforzado. ...

request motor base https://www.banggood.com/Syma-X5-X5C-Motor-Base-Spare-Part-4PCS-p-978463.html?rmmds=search&cur_warehouse=CN F3 Evo brushed motor...

Some propeller caps were missing when I received my kids Syma X5HW. ...Designed with Tinkercad.

Some propeller caps were missing when I received my kids Syma X5HW. ... Designed with Tinkercad.

Version 2 de mon drone sur base de Syma X5 Reprend les composants mécaniques et électroniques du syma X5 (22€ sur banggood) Il est uniquement nécessaire de dessouder puis ressouder les fils moteur pour les faire passer dans les bras Les assemblages...