synology drive caddy 3d models

The push to lock / latch on the Synology drive caddy / tray is broken and this is my 1st attempt to fix it. Although it needs some clean up after done printing, amazingly it does work! Also you can contact Synology (even out of warranty) and they...

Hex key for synology nas hard drive bay

I have some drive trays from a used Synology NAS that never had these, and new drive trays are expensive. ... This is unrelated to https://www.thingiverse.com/thing:2397737 so IDK if they'll work together.

... ______________________________________________________________________ Replica of the HDD locking system for Synology NAS drawer. ...This version is specifically for the 2.5 "hard drive adapter (https://www.thingiverse.com/thing:4831668).

... à l'adapteur pour disque dur de 2,5" (https://www.thingiverse.com/thing:4831668). Replica of the HDD locking system for Synology NAS drawer. This version is specifically for the 2.5 "hard drive adapter (https://www.thingiverse.com/thing:4831668).

Remix of kai's HardDriveHolder D7, which didn't fit in my DS1815+. It is not that pretty, well, it was, as it came from kai, perhaps I will do some further improvements. But in this state it will work just fine. Appreciate to get some input from...

I lost my original keys (found them eventually) so I found a few 3D printable ones, but I didn't really like them, They were nice and functional, but I wanted more of a standard key looking one that could sit on a keychain. There are 3 different...

Lenovo does not sell drive caddies. So I printed my own. ...They allow airflow and hold onto the drive well enough to pull the drive out no problem.

This is a replacement drive caddy for the Corsair750D case. Print in PETG if possible. ...Use either rubber mounts or the propper screws for mounting the hard drive

This is a very simple design, a caddy to hold up to four external 2.5" hard drives. Whenever I buy a new laptop I immediately swap out the standard hard drive for a solid state drive. I then buy an enclosure for the HD I just removed and convert it...

*Work in progress - Untested Print* This is my attempt to build a 3D printable drive caddy for Atomos SSD recorders, I am modeling this off the one from my Ninja Blade.

------------------------------------------------------------------------------------------------------------------- Here is an adapter to be able to use 2.5 "hard drives or SATA SSDs in Synology brand NAS and using drawer racks. ... This notably allows...

... qui ne possède pas de connecteur M.2. Here is an adapter to be able to use 2.5 "hard drives or SATA SSDs in Synology brand NAS and using drawer racks. ...This notably allows the use of cached SSDs for models that do not have an M.2 connector.

I used the stock Antec Hard drive caddy and redesigned it to be more 3d printable. ...I took the clip out due to it not working well in PLA, but the print is a snug fit and holds the drive in well.

3.5" drive caddy modeled to fit Dell Optiplex 5050 SFF. Likely fits more models, but could not find the original part number to make a compatibility list. Uses standard case screws to attach drive. ... Recommend printing in PETG for flexibility, so...

I bought some of [these](https://www.amazon.com/gp/product/B00T4SZ720/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1) SAS caddies for my Lenovo SA-120 drive bay. Unfortunately, the side clips are very fragile and I had a few broken just pulling the...

... mountable. Sourced from: http://hackaday.com/2013/07/27/10-drive-microserver-is-the-clown-car-of-the-computer-case-world/ Instructions Just use support material, and ideally, have the back side of the caddy facing down towards the build platform.

I have a T310 that needed to have a couple of drives added so I did my best to make a quick drive caddy so I could make that happen with some SATA drives I had laying around. The layout is based on the F238F drive tray that is in the system. There...

So, here is a quick and easy RAW drive caddy. Just to set your expectations, this is not a case or adapter of any kind. It is just a plate that covers the underside of the drive to protect the drive electronics as well as your nice table top. The...

Decided to play around with my supermicro drive clips and came up with these after a few dozen alterations they seem to work pretty well There are two variants of the drive latches a long one thats a bit tricky to swap out, takes a bit of patience...

For 10 hard drives

Pièce de rechange du systéme de blocage des HDD pour tiroir des NAS Synology. Cette version est quasiment identique à la pièce d'origine, mais qui ne semble pas être vendu sans le tiroir. HDD locking system spare part for Synology NAS drawer. ...This...

... ______________________________________________________________________ HDD locking system spare part for Synology NAS drawer. ...This version is almost identical to the original part, but which does not appear to be sold without the drawer.

Holds 9 thin and 7 larger thumb drives.

Had some hard drives sitting around a needed a place to store them. ...This is my first 3d model so cut me some slack :) This will only support 3.5drives

This caddy is for mounting a 2.5" drive in a 3.5" drive bay.

Dual hard drive or ssd caddy to help clean up lack of mounting space or just for ascetics

Corsair-750D-Drive-Caddy This is a 3D model of a drive caddy designed to fit into the 3.5" bays of a Corsair 750D and related cases. ... This model is coded/designed in Openscad.

Drive caddy storage for SD cards, USB dongle, and other small items. Fits Lenovo T440p. ...May fit other laptop disk drive slots.

Hard drive caddy for the 2nd bay of an Hewlett-Packard Zbook laptop. ... Instructions print 100% fill, no raft, with supports, .2m layer, 2 shells