t5 hammerhead 3d models

Both the motor end pulleys had key ways cut in them with a fret saw using a supplied pulley that came with the servo as a guide. ... they both work but give different speeds, I'm using the smaller one at the moment and its fine.

remix from https://www.thingiverse.com/thing:4749075 My changes: - smaller walls - buttons extra to print - add stand - optional backplate - board holder little bit thicker for screw M3 8mm This angle type C cable fits perfect =>...

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

Customized version of https://www.thingiverse.com/thing:5115076 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5115076

https://www.thingiverse.com/thing:4441076 presented a thumb screw to replace the wing nut on the front-left corner of the BIBO bed. It is too wide for the other two positions. I have created a smaller version to fit the right-front corner and the...

The shift adapter is best printed in ABS, ASA, or a high-temperature CF-reinforced filament, as this takes all the strain of gearshifting.  I printed the ice cream in BambuLabs TPU 95A for a softer grippy feel (and it works great). ... Cone is printed...

If you're replacing old tubes, I figured it can't hurt to reuse the reflectors and direct a bit more light downwards. Wanted to lift the lamp slighly so the reflectors don't create shadows if it was mounted flat to the metal. Also saves the hassle...

After upgrading my thermostat, paint was stripped off with the old, wider thermostat (see "before" photo)... So I figured instead of repainting it, I'd come up with a creative solution instead. This is the solution I came up with, a decorative...

Customized version of http://www.thingiverse.com/thing:16627 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=16627 Instructions Using the following settings: Additional tooth width is set at 0.2. The distance from...

This is a sleeve I designed to house my SSD while sticking it to the back of my MacBook. This was to avoid my hard drive flopping about any time I walked around with my laptop and hard drive still attached. ...I used velcro to stick it on.

Customized version of https://www.thingiverse.com/thing:5275619 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=5275619

Customized version of http://www.thingiverse.com/thing:343343 Created with Customizer! http://www.thingiverse.com/apps/customizer/run?thing_id=343343 Instructions Using the following options: Belt idler set to standard position. Base height is...

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627 Fits on NEMA17 17HS13-0404S-PG5 geared stepper motor for MOVEO robotic arm

rotate 90 degrees, lay flat on bed, use supports made by cura. ... My first creation in Tinkercad, first upload, if u see an opportunity to help me and this design further, let me know!

I cannot create, generate, spin or write content for you as that would be AI assisting a piracy attempt.

Customized Version of a Mechanical Pulley System Created with the Customizer App on Thingiverse: A Platform for Design and Sharing of 3D Printed Models **Instructions** To Use this Modified Pulley System: 1. Select Options: * Set Idler Count to...

Customized version of https://www.thingiverse.com/thing:2682637 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2682637

This is a TPU protective shield I designed for the Thieye T5e remote, crafted specifically to keep it safe while being carried on a keychain or other accessories - it lacked an attachment initially. ...Constructed from high-quality Sunlu's TPU+...

Customized version of https://www.thingiverse.com/thing:16627 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=16627

Customized Version of the Pulley and Idler Set Created with Customizer! ... **Instructions** Using the Following Options: - Retainer Size: 1 - Additional Tooth Depth: 0 - Pulley Block Diameter: 50 - Pulley Block Height: 14 - Tooth Top Height: 20 - M3...

<p>Make Your Own Custom Charing Station using these 3D Printed clips</p><p>Go have a look at your current charging setup now, I bet the wires are all tangled!</p><p>I have included designs for a basic charger station that has cable channels on the...

A Hook for your VW bus -Bigger Diameter -Pinch Ribs -More stable