tab and slot 3d models

Tabs are to be used with a union (add material to an object) Slots are to be used as a Difference (take away material from an object) Instructions include this module into openscad project use the tabs module to add tabs (union) and the slots module...

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

1/4" thick plate with .001" oversize slots.

(If you scale them down just a bit, they might snap on and stay without gluing.) I made a new F1 floor - this one is a little larger, and more importantly has slots for the walls to fit into, to help with alignment and stability while gluing. The...

Customized version of https://www.thingiverse.com/thing:39808 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=39808

I've also added two tabs on the base for gripping while adjusting the outer ring so that the inner ring doesn't spin as well. The last modification I made was a slot to hold a 9x2mm magnet in the bottom of the base. This is for position snapping...

 This is a remix of (https://www.prusaprinters.org/prints/32179-raspberry-pi-34-b-case-with-slot-for-camera-cable) which is a remix of (https://www.prusaprinters.org/prints/24942-raspberry-pi-34-b-case)Added two tabs for mounting.  You will...

Just another cd slot phone holder. This one is for Samsung Galaxy Tab S2. ... One is with three braces, the other one is with only 2.

-Narrowed wire/cable slot at base, so as it holds the cable and stops it from making the holder sit unevenly on a surface. Feel free to mod to your delight. ... Original remix mods: -Raised up to make room for charger underneath -Raised front and rear...

The inset is designed for two things: 1) reduce material used during printing and 2) a place to put text when customizing for specific games. ... FUTURE TODO: - Additional options for where to put insets (top/sides of lid, bottom of box, remaining...

a tab holder that never looses contact with the table ,even if dragged across the table

It is a model based on the icon of Facebook, can be assembled, one is a keychain, since it has a hole to use it as a keychain, and the other is simply assembled and remains as a tab.

It is a key ring that has the WhatsApp logo and the other is a token, can be assembled and has a design so that it does not consume much filament.

A safe and easy way to open cans without finger or fingernail damage. The usual simple bottle opener. ...For my wife.

Remix of https://www.thingiverse.com/thing:4275741 Filled holes and created slot for allow easy removal for 3M Command strip.

Tab Can Opener - tab lift and lid pull support I found some tab can openers, but most of them are only designed to lift the tab, which is fine for soda cans, but if you want to peel off the lid, I only found hook-like stuff which still need a lot of...

tab

tab

tab

Tab

Tab

my tab

Tab for wall

Hey everyone. ...Tried to design something like a tab. I expect everyones kind suggestions. ...Thanks

En verdad es mi primer subida al sitio. ...Es un tab personalizado, marcas cada 5 mm espesor 3mm