table bag hook 3d models
183172 3d models found related to table bag hook.myminifactory
Table Bag Hook A hook that hangs from a table or shelf that holds your bag. ... " I DONT LIKE PUTTING MY BAG ON THE FLOOR" is written on the outside!
thingiverse
This is a tool for hanging the bag on the table. It's foldable so you can carry it around. ... The shape of the teeth keeps the balance even if it is about to come off the table.
prusaprinters
<p>The original design was weak for me near the top, so i make it more stronger.</p><p> </p><p> </p><p> </p><p>I print with 0.6 nozzle, 0.3 layer high, 4 perimeters, 4 top and buttom layers, and 10 % infill gyorid.</p>
thingiverse
No supports needed Two versions, take a look at your table whether it has a gap between the table boards or not
prusaprinters
This table hanger/hook is for everyone who doesn't want to put their bags on ground at bars. This small design comfortably fit in pocket and there is small hole for string to attach it as well.</p><p>You can see the print file for Průša mini+. Print...
cults3d
Folding miniature handbag hook ladies like to use when going out. ...No plonking on a spare chair or have it go missing when out of sight, just hang the handbag at your elbow on the table edge.
thingiverse
A hook wich can be mounted under a desk or table to store bags & stuff
thingiverse
I wanted my trash bag for wasted PLA to hang on the desk where I need it, so I designed a couple of hooks for a table 24mm thick. The fillet on top of my table has a radius of 4mm. The hooks both go 30mm "deep" in the table. AFTERNOTE: I noticed...
thingiverse
a hook under a table to tie his bag un crochet sous une table pour attacher son sac
thingiverse
It's an update to the previous hook I designed to hang my PLA trash bag on my table side. It turned out they don't have enough force to hold on properly anymore after few weeks, so the gap is now 3mm smaller than the table (was 2mm / 2,5mm). Also...
thingiverse
Bag Hook for Ikea's Linnmon Table. Suitable for 34mm tables. ... I use PLA.
thingiverse
This is a table hook that accommodates bags/purses that have a wider strap. Instructions Once you print it, the hook piece should be press fitted into the round piece. Optionally, you can apply glue or ABS juice before press fitting the pieces...
cults3d
I don't have a picture of this print but functional, they are used at my taff no worries for the moment, support my blue jacket, and the other part support my small backpack.
thingiverse
This is a bag-hook for suspending your bag under a table so you do not put it on the floor. It works okay but i would probably tilt down the top part by 10-degrees if i print again. It is surprisingly strong printed by Shapeways in the versatile...
thingiverse
I needed a hook to hold a rubbish bag on my PC/Make Up trolley so came up with this. ... Basic, chunky and does the job.
thingiverse
Not going to be hanging the bag from this hook but just something to reach it easily and existing hooks did not do what I wanted. This was cut from 5.5mm stock. ...If your stock has a different thickness you will need to go in the .f3d file and...
thingiverse
Bag hook that I modeled for the exact thickness of the desks where I work. ... That will have to be edited based on the thickness of the desk you want to clip it to...
thingiverse
A simple hook to store your bags behind the driver or front-passenger seat with the headrest mount. Fits perfect on all Volkswagen cars. ... Width of the cut out is about 14mm, so your bar of the mounting should be around that diameter.
thingiverse
A folding hook to hang your bag on the edge of your desk. From before the remix, the size is the same and the strength has been increased. It's a slightly more design-oriented design. Just barely enough to be able to use it as a smart phone...
thingiverse
http://www.thingiverse.com/apps/customizer/run?thing_id=1367661 Instructions Using the following options: thickness = 69.1 tolerance = 0.5 second_hook_angle = 0 second_hook_lenght = 0.1 bracket_size = 40 stop_lenght = 15 screw_diam = 10.5 screw_head...
thingiverse
Simple closet rod hook for a backpack. This thing was made with Tinkercad. ...Edit it online https://www.tinkercad.com/things/2wuNmbQLsrg
thingiverse
I hate going to the restroom and finding that the hook on the back of the door is broken and I can't hang my purse. So I designed this hook which will hold my purse off the floor and hang on the door. ... :)
thingiverse
Edited original design of U-Hook to fit and snap on click on to 25mm desk top. Strong part, prints well. ...Designed to hold the backpack Includes stl to part with and without front decoration.