table vice grip 3d models

Vice grip hand tool

Re-design vice grip with solidworks 2013 with rendering

Simulation of Vice Grip in SolidWorks. ...The tutorial is here http://grabcad.com/questions/tutorial-simulation-of-vice-grip-in-solidworks

Just a standard vice grip. ...I did not have access to standard bolts and nuts so the fasteners are missing on the vice grip plates.

cnc-vice,

wanted a handle for the excellent PRIma vise/vice so I could take it off the desk and hold it when painting some times. Print both upright no need for supports. Use some CA glue to join both together, then just unscrew your vice/chuck and attach.

Table Vice

Table Vice

Vice Grip model with nominal trademark. ...Solid Edge ST7

Remix of a table vice I found. ...I strengthened the base with solidworks since the original was bending too easily

A completely portable vice grip that can be used anyone there is a table. This amazing design also allows for use of objects of almost any size. ...The only limiting factors the table and the size the screw, which can be easily printed to any size.

A part I modelled to replace old worn-out vice clamp grips.

A part I modelled to replace old worn-out vice clamp grips.

3d model iron vice-grip. Textures 4k. ...Diffuse+Normal map+Specular+Gloss

This foot should fit most Vice Grip welding clamps with the swivel foot.

A part I modelled to replace old worn-out vice clamp grips.

I have had a set of vice grips that the foots rusted off, I made these to replace them.

Modification of the grippers of the vice grip such that they can accommodate irregularly shaped parts for the purpose of machining. ...

Custom vice grip or Pliers holder for a pegboard. A little less than 6mm so it easily fits in a pegboard. ...Best printed on its side.

Simple vice grip pads for a Bessey Gun Vice. Reinforced edges on face, slight offset holes and 1 bottom corner has a slight bevel to snuggly fit into the vice. ... Designed in TInker Cad No supports needed 20% fill, PLA or preferably PETG

A very simplistic design of a magnetic vice grip. ...I designed this unit some time ago, with the aim to assist the workers by reducing the down time during the changing of the material during fabrication of various componentry.

The vice is 60 * 100 * 30mm with a clamping space of 60 * 70mmI printed the spindlethreat with 100% filling, the rest with 20%Assembly instructions:Vice:The base, guides and fore jaw are one whole.Turn the spindle treat through the treatbase from the...

The vice is 60 * 100 * 30mm with a clamping space of 60 * 70mm I printed the spindlethreat with 100% filling, the rest with 20% Assembly instructions: Vice: The base, guides and fore jaw are one whole. Turn the spindle treat through the treatbase...

Works fine for Wolfcraft vice. ...Add a bolt for fixing.

3D Recreation of the vice grip hood ornament as seen on wired.com. Tongue prints separately and should slot in with a touch of adhesive Not yet engineered to actually be mounted on a car. Present version designed as desk ornament; I'd...

I had issues with the rubber band getting under the vice and jamming on the original so i made a version to fix it.

Hello Magnetic vice jaws. You need to pause your printer to embed 8mm diameter by 2mm high round magnets. ... You have 3 models with 3 lengths, 100, 125 and 150mm.

Vice-grip_for_repair_cardan was used in an installation for repairing cardan joints (for dismounting needle bearing housings).

Vice grip to make it easier to hold your figures while painting them. No materials required other than 3D printing ;) Easy assembly: 1- put the screw in the hole of the jaw 2- lock it with the wedge by passing the wedge through the square hole under...

Dimensions of the model are taken from the "SolidWorks for designers" by Sham Tikoo (© CADCIM Technologies,2006)