tablet charging rack 3d models
68934 3d models found related to tablet charging rack.thingiverse
I wanted to tackle the messy pile of tablets and charging cables that built up on my kitchen counter so I put together this simple rack in TinkerCAD. The rack holds 4 tablets or phones and have made the slots wide enough to accomodate most cases. If...
thingiverse
A simple charging rack for tablets and or phones. The circle is meant to store one of those rechargeable portable batteries. Print Settings Printer Brand: Robo 3D ...
thingiverse
This is a rack for holding phones, tablets, and similar devices for charging. It's designed to have an [Anker USB charger](https://www.amazon.com/Anker-Charger-PowerPort-Multi-Port-Samsung/dp/B00VH8ZW02) popped into it; it will hold the charger in...
thingiverse
Customized version of https://www.thingiverse.com/thing:2637934 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2637934
thingiverse
Customized version of https://www.thingiverse.com/thing:2637934 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2637934
thingiverse
Customized version of https://www.thingiverse.com/thing:2637934 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2637934
thingiverse
Customized version of https://www.thingiverse.com/thing:2637934 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=2637934
thingiverse
Ich habe das sehr gelungene Design unverändert von " jordanbrown, https://www.thingiverse.com/thing:2637934" übernommen, da die Smart-Phones und Tablets dort mit Hülle oder Tasche rein passen, sogar meine kleinen E-Dampfer passen da rein. Dafür...
thingiverse
Removed smaller rack slot and resized to fit Kindle Fire 5th gen with Freetime case
thingiverse
... print in the most flexible, polymer-like filament you have. this allows the rack to adapt to different-sized devices. For any M3D users out there, make this in Tough Ink. ...Post-Printing Video
thingiverse
My tablet only charges if I bend the plug forward. So I made some bending device. ...;)
grabcad
Tablet Charging dividers that we use to store our Fire HD 8 tablets for scouting. The divider sits in side of a Sterilite bin along with the charger and cables for the tablets. ...Its made from Laser cut 5mm plywood.
thingiverse
You can charge your phone or tablet. ...its big enough to hold it horizontally, and there is a hole coming through the back for the cord to run through.
prusaprinters
Just a simple stand to hold up to four tablets or phones while they are on charge.The slots are 12mm thick and will accommodate most tablets and phones, even in a case. There is a cable management slot at the rear.</p><p>Print on its edge. ...No...
prusaprinters
This is a redesign of jmlee3k's Tablet Charging Station.Printed on an Ender3Pro.04 mm Nozzle.28 Layer HightIIIdMax PLA+ in Space Grey and Night Grey.
prusaprinters
This modular stand holds one or more tablets for charging; the tablets can be up to 14mm thick. I also included a recess in the rear to hold a charger (27mm x 90.5mm); I made the recess specifically for my charger so of course some chargers will not...
prusaprinters
Made this to hold kindles upright for compact charging as well as protecting cables / ports from little hands. ...Two wide ports for the bigger bumper designs, as well as a few thinner ones for phones and non-case tablets. Uses multi-port usb brick off...
thingiverse
The Smartphone & Tablet Charging Station dimensions are 20 x 13 x 6 mm. Can hold several smartphone (up to 10), reducing mess and cable crossing. I 3dprinted with CTC Bizer (a clone of Makerbot) at 0.30 mm resolution. The bottom required around 13...
thingiverse
... the hole should be large enough to fit most chargers. Depending on where you will place it, the cable can be redirected to either side or to the back. The pieces are 6mm thick, so with a little infill structure it should hold even heavier tablets.
thingiverse
... for lots of different devices. The slots are 15 mm wide so as long as your device isn't thicker than that then this will work. It also includes a slot on the bottom that you can feed a charging cable through so that it doesn't fall off the table
thingiverse
Simple stand, made for my HoneyPi tablet, that allows the phone/tablet to be charged.
thingiverse
A very simple but effective rack for storing iPads, tablets and Laptops safely. ...The inner dividers easily accommodate a tablet device with a case and the outer two a laptop of average thickness (it won't store some of the chunkier gaming laptops)...
thingiverse
i used this to wall mount my switch by my bed to just have it there feel free to modify the file in any way just make sure to link back to me its a pretty simple file to make it has a charge opening at the bottom too i reccomend if your switch isnt...
thingiverse
Incline angle about 45˚. ...Also works fine with my 8" tablet and 10* tablet.
cults3d
It's a holder that allows you to charge five laptops, tablets, MP4 players, and more. ...It has five slots, one of which allows you to view your tablet or smartphone.
thingiverse
Store your laptop (max 24 mm) and tablet (max 12 mm). ... Fit my Dell XPS 15 (2020).
cults3d
Phone and tablet holder designed to attach to an Anker USB charger*. ... *affiliate link
thingiverse
Phone and tablet holder designed to attach to an [Anker USB charger*](http://amzn.to/2zTKPju). ... **affiliate link*
thingiverse
A 4 phone charging rack. Two widths available 24mm or 48mm. Will fit most phones with cases 14mm and thinner. You will probably want to print the 24mm version in a pair to keep it from tipping. ... The 48mm version should be wide enough to be stable...