talion v3 3d models

This is a strong servomount for the talion 2018 v3. You have to cut a little piece of the esc-mount plate to make this part fit in the car. To mount the servo in this part you have to open the servo and dismount the upper part of the servo. just...

special for the arrma talion or kraton front or rear would appreciate it if you print this please let me know,, PLEASE DO NOT SELL MY DESIGNS, THANKS, happy speed runs

I recently got myself an Arrma Talion v4, and took it out for some bashing. As soon as I took it out a few times, the wing broke off, and kept breaking off. I couldn't find any good mounts except for one wing mount for the Kraton (Which can be found...

Since the suitable hardcase packs from hobbyking where not deliverable i ordered a standard 4S turnigy battery-pack and designed this hardcase for my talion v3. I printed it for each of my battery packs and leave the battery inside. The design fits...

Center mudguard for Talion 2018 with a simple mount solution. ... the chassisbrace part you see in the picture is just work in progress; so wait a few hours ;-))

special for the arrma talion, ((((note the support for warping does not work with this print,))) left and right Mud Guards would appreciate it if you print this please let me know,, PLEASE DO NOT SELL MY DESIGNS, THANKS, happy speed runs

update 19.02.2019: added a stronger version around the screwholes i just did a little remix of the great design from dionlevi. ... with this design you can reduce the printing time ;-)

All you need is about 40cm of an alloy U-profile with 10x10x2mm and some m3 screws.for mounting the rear part you have to dismount the wing holders. ...to put the brace between the shocktowers open one screw of the original rear brace to get the new...

Arrma Talion v3 Desert Mod (other models possible, not tested) Here I present you my modded Arrma Talion. For this mod all you need is the Reely RE-5690550 Cage, some m3 screws for assembly, the linked files and a low profile wingmount (AR320379)....

update 15.06.2019 - added inlay for the wing bracket - added sidepanels; roof and bonnet in a textured version - added a link to the remixed version of the wingmount from tux3r Arrma Talion v3 Desert Mod (other models possible, not tested) Here I...

Litofania Talion from Lord of the Rings .

Sidewalls for Talion EXB

2018 Arrma Talion rear Mudguards, uses the 2 spare M3 screw holes in the rear A-arm to mount the mudguard.

Update 23.06.2019: added a version that fits perfekt on my sideguards and othe small improvements (https://www.thingiverse.com/thing:3680208) This is a center Mudguard for my Talion Desert mod. ...But i think it fit also on standard Talion, eventually...

special for the arrma talion, please just rotate it on the print bed,for the best print, front and back would appreciate it if you print this please let me know,, PLEASE DO NOT SELL MY DESIGNS, THANKS, happy speed runs

This is a servo mount for arrma talion, remixed from djdj111. I just changed the front lip so it doesnt sit on the side guard. I have not printed yet. you will still have to cut the esc mount a little bit to get this to fit.let me know if you print...

2018 Arrma Talion rear Mudguards, uses the 2 spare M3 screw holes in the rear A-arm to mount the mudguard. Versions Normal: Mk5: Vertical only ribs for ease of cleaning and rigidity. Mk6: Vertical and horizontal ribs for extra rigidity. Tight Fit:...

A simple adapter to use two 35mm fans on Talion EXB. ... the fan guard with spektrum logo you can find here: https://www.thingiverse.com/thing:5400591

Mudguards for the 1:8 Truggy Arrma Talion. Probably fits the Senton and Kraton as well, but haven't tested that. ...You might have to use a conical shaped tool to enlarge the holes some.

Roof sliders for Arrma Talion EXB or any other rc car. ...Just drill the holes into the bodyshell through the top an fix the sliders with M3 screws and nuts.

ESC Cooling Fan Cover, I designed this especially for the Arrma series, (talion kraton etc ) I only do speed runs with my talion so extra cooling is always good, it can be printed in different Heights, you do not have to remove anything, this can be...

These are raised rear body posts fitting the Kraton/Talion rear tower bridge. Very stable and durable (make sure to print with 100% infill). Use some support to print, it's a bit sketchy to print but works out in the end. ...Print Settings Printer: ...

V3

Just mirror the stl for the other side... ...

Customized version of https://www.thingiverse.com/thing:4381135 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=4381135

Arrma Talion Low Profile Rear Wing Mount Arrma part #AR320379 This design braces the mount upper surface against the shock tower for increased strength.

Because the version of tux3r is breaking away at the holes every time on my modded Desert Talion, i added some thicker walls an printed it in PA-CF. Now the Wingmount is very stable and after some testing i can say, its realy robust. ... Happy...

V3 low poly vase to papercraft

Print this wing mount with flexible filament. You will need two longer M4 screws. ...

... the stock screws for mounting with a washer from the bottom because the hole in the center of V1 creates a weak spot and it's prone to breaking. 15/01/2020 - Added V3 which is essentially the same thing to V2 but with slightly better clearances.