tandem tslim x2 case 3d models

This is a case for a Tandem T:slim x2 insulin pump. I broke mine so I set out to design a new one (I didn't want to wait the 2 weeks to get one shipped.) Luckily it's only taken me 3 weeks to design and print this :-) The case is designed to be...

Remixed version of the Tslim case by DonBroyles: https://www.thingiverse.com/thing:3124611/files I removed part of the case to eliminate the need for this to be printed in flexible filament. The pump should just slide down from the top. I also made...

I liked the design of the case by DonBroyles here: https://www.thingiverse.com/thing:3124611 but I prefer to wear my case horizontally. Use his print settings for the TPU case and PETG for the case clip. ...I used a 50% infill on the clip and 3 walls.

Remixed to protect the front LCD. ... Works well printed with PETG.

Wall Mounted Charging Station for Tandem Slim X2 insulin pump. Two versions-- Version 1 fits a pump with the T:Case or T:Holster. ...Version 2 fits a pump with no case.

just a simple case for a tslim pump that can hold a airtag. In many of the t1d support groups I'm in I've seen parents talk about their kids taking off their pump for gym class and misplacing them. ...The pump slides in the case face in so...

Tandem t:slim X2 accessory tray

A drawer container to hold one box of Tandem X2 Inslin cartridges, and the associated syringes. This box is of a form factor to match my Tandem X2 Infusion Set supplies. ...(https://www.thingiverse.com/thing:3616002)

My wife's original Tandem T-slim case broke so I decided to make another one and share the file so anybody can print one off. ...Enjoy!

Tandem X2 Upright Cartridge w Cutout No Pin Has a cutout so you can access the 1 to unlock pump. Has no guide rails for cartridge. This is easier to use if your printer isn't very accurate. Tandem X2 Upright Cartridge Has no cutout. Has guide rails...

This is an organizer for Tandem T:Slim X2 supplies (Autosoft XC & Cartridges). I've included the full file that I printed, along with some segmented pieces and simple file. You choose to print what you want. The organizer will hold 5-6 inserters...

... of my friend, I carried out a dynamic analysis of 4 schemes of a 2 cylinder piston engine. ...The analysis files were not saved, and the result was obvious. Normal - this is a TANDEM scheme and a BOXERBut MONO and SINCHRO - disbalance is unacceptable.

Case for Sidewinder X2

A full-size case for the AUAV-X2 Flight Controller, a very compact Pixhawk-Clone. All pins and sockets are protected. No screws needed, top and bottom shells click together. ... The FC sits snug within the case, but you can use short pieces of 2mm...

A simple case for the Odroid X2. It is printed in two parts, a top and a bottom, which fit together and can be attached together permanently with screws or glue. There are screw holes to mount the Odroid that accept #4 screws. Also, a large circular...

Protective dual travel case for 18650. ...If you have your batteries in shrinking tube, then you should scale this file up for ~1.05

No screws needed, top and bottom shells click together.The FC sits snug within the case, but you can use short pieces of 2mm carbon rod and stick them into the holes prepared already for that.

These Batteries are used in the Key Fob of my Car and I wanted to have 2 spare batteries stored in the car in case a Key Fob Battery gets empty while on holiday. It was designed with Freecad (please someone should add this great Open Source...

and using TPU just new to Ender 3 v2 13-14 hours out of 16 for my setting case and top printed same time no need for supports, will fix if i have issues with the case but the shashibo should stick out 3mm like i designed it to to hold the top in...

These Batteries are used in the Key Fob of my Car and I wanted to have 2 spare batteries stored in the car in case a Key Fob Battery gets empty while on holiday. It was designed with Freecad (please someone should add this great Open Source Program...

So made up this little case for it, all the openings are accessible, the Micro SD card slot, the reset hole, the Micro USB for charging and file transfer (made to fit the stock plug that comes on the cable with it) and also a hole for the headphone...

This one might not yet fit well (to be tested, please post results in the comments) thanks to aurelioponz for helping me with this one :) Update 2013-04-07 ~12:00: new v0.1 design (might still not fit, just some stuff added) Update 2013-04-07...

use 100%infill to make it stiff enough to work. also might want to go over the tab whit an soldering iron to fuze the layers together as it will brake after use. ... (might be less of a problem whit abs and petg but pla tends to become brittle after...

It is mainly designed for twin cameras in the use of tandem handcam footage. Gloves can be purchased online and your friendly DZ rigger can improve them a little. To mount these I have used PU glue and some aluminium riveted in place. Super...

This is a case for the Oppo Find X2 Lite. Print it with TPU filament. ... Print settings: - 0.3 mm - 100% infill - supports

Here i made a case for the ESP-12F_Relay_X2 module. There are 2 versions of the lid, one with a additional hole for a extra pair of contacts. ...I use it for a extra switch input.

This case with a lid will hold two each of an Altus Metrum Mini or Altus Metrum Timer

deux petits coeurs en tandem. ... Imprimé avec Ultimaker 2Go et filament PLA argent.

Summary Deux petits cœurs en tandem. https://www.youtube.com/watch?v=az4uAoqPKYY Très facile à imprimer, vous pouvez prendre une échelle plus petite. Imprimé avec Ultimaker 2Go et PLA argent, buse de 0,4 mm. NOP21 Two little hearts in tandem. Very...

Deux petits cœurs en tandem.https://www.youtube.com/watch?v=az4uAoqPKYY Très facile à imprimer, vous pouvez prendre une échelle plus petite. Imprimé avec Ultimaker 2Go et PLA argent, buse de 0,4 mm. NOP21 Two little hearts in tandem. Very easy to...