tape and bed 3d models

A small plastic scraper for wiping down the tape on your heatbed, to make sure it's stuck properly.

JUST A LITTLE TOOL TO SMOOTH OUT THE TAPE WHEN FITTING TO THE PRINTER BED

Purpose: Pat’s ultimate sticky tape dispensers’ primary purpose will be storing tape and cutting it to the size required by the user. This will happen when force is applied on the model and the cutting blade. Target audience: My project will...

... resistors. And with the paper tape. But you've got the solidworks model. Feel free to size it to your needs. ... I use the 1.5 dram vials (PN: 66011-063) https://us.vwr.com/store/product/4618574/vwr-vials-borosilicate-glass-with-phenolic-screw-cap

I'm always searching for a roll of electrical tape or a solder spool in my shop - search no more. The next in my pegboard series - you will need two of the pegboard pins. ...Print Settings Printer Brand: MakerBot ...

Instructions Order the tape @ Updated LInk 08/25/2014: http://www.laserbits.com/laser-supplies/masking-materials/sus-063-polyester-rigid-mask-medium-tack-6-in-25-yds.html Remove old tape Clean bed with acetone and lint free cloth Use this...

This roller and pin were designed and printed to remedy my tape dispensing dilemma. Instructions Printed roller pin horizontal to print bed. ... Created in Sketchup Sliced by Cubex printed on CubeX Trio 30 minute print time PLA 4.29g .25 layer height...

Simple tape measure and pencil holder that can be mounted to a wall with two screws.

... tape holder for the workshop. ...I made a large opening for various marking tools and a side compartment for a carpenter's pencil. No, this does not completely help you find your lost measuring tape and pencil you just had, but it does help!

This is a office tape holder/dispenser. ...It's designed to accept tape rolls with ID of >26mm and OD < 55mm and piece of upholstery knife as a cutting edge of the dispenser. Feel free to remix it however you want. ... No supports needed.

This is a office tape holder/dispenser. ...It's designed to accept tape rolls with ID of >26mm and OD < 55mm and piece of upholstery knife as a cutting edge of the dispenser. Feel free to remix it however you want. ... No supports needed.

... this bowling case to hold my tape, scissors, tools etc. ...It fits nicely into the zipper side of a bowling bag. The body is printed in ABS or PETG (to survive car temperatures). The shell and lid are printed in flexible TPU, like a Tupperware lid.

I made inserts for the tape and kitchen roll so they all sit correctly though this is not essential. Printing: I printed at 0.3mm resolution and 40% density (this was a guess and is almost definitely not optimal). I recommend printing the parts on...

The two parts of this fit together to keep the sewing tape inside. ...Best to print the two parts separately, use the split feature in Cura to make two separate gcode files.

Takes about 8 Hours (7 Hours and 56 Minutes) with a low res 0.28mm setting and 10% infil. Created this as a project for a 3D printing Final in school, and thought someone else could possibly use this. Holds 4 CD cases and 3 Cassette cases. ...

Gridfinity System | Tape Spindle Holds electrical and plumbers (teflon) tape. Made to fit shallow drawer depth. Can support 2-3 spools of tape. ... Free, Editable Design Files Available @ TheModernFrontier.com

Protects your tape from dust and being damaged. This caps fits perfect to Blue Tapes. For other tapes you might simply adjust the parameters in Customizer. Why not branding it with your name, school, shop, homepage or something else. A separate...

The actual print size depends on the many factors of print settings, but the designed sizes allow for a good range of sloppiness, and functionally, a loose fit here is as good or better than a tight fit.If you will only be using blue or masking tape...

... to be mounted under a shelf. ...simply pull out and reset the pull everything is sitting on. just. also made to hold cutters (razors or cut saw blades) for easy quick cutter of tape. ... Cutout version also has a holder for wires to hang down into.

http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: dot_diameter = 2.4 text_font = orbitron.dxf wallthickness = 1.2 text_thickness = .6 outer_diameter = 120 inner_diameter = 76.5 height = 10...

http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: text_font = orbitron.dxf inner_wallthickness = 2 inner_diameter = 76.5 dot_diameter = 2.4 dot_number = 8 outer_diameter = 120 label2 = 3D...

http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: text_font = orbitron.dxf inner_wallthickness = 2 inner_diameter = 76.5 outer_diameter = 120 dot_diameter = 2.4 dot_number = 8 label2 = 3D...

http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: wallthickness = 1.2 outer_diameter = 120 text_font = orbitron.dxf text_space_factor = 1.1 dot_diameter = 2.4 height = 10 inner_wallthickness = 2...

http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: wallthickness = 1.2 inner_diameter = 77 outer_diameter = 130 height = 20 dot_number = 12 text_height = 12 text_space_factor = 1.1 dot_diameter =...

http://www.thingiverse.com/apps/customizer/run?thing_id=691124 Instructions Using the following options: inner_wallthickness = 2 text_font = orbitron.dxf inner_diameter = 72 outer_diameter = 95 dot_number = 8 dot_diameter = 2.4 label2 = 3D Printing...

All you need to do then is attach some wire to your LED tape and connect it to one of the spare 24v output and ground terminals on the internal power supply, Voila, bed lighting. The piece has such a small footprint I had issues getting it to...

Makergear M2 Tool and Tape Holder

Print the bias tape/ribbon holders with a .4mm nozzle and .2mm resolution. The tray itself for speed I print out with a .6mm nozzle and .4mm resolution. You'll need a brim since the way it prints will likely result in warping at each end, even with...

http://www.thingiverse.com/apps/customizer/run?thing_id=1148986 Instructions Using the following options: Rotation = 50 letter_3_height = 4 twist = -3 letter_1_height = 6 Loop_x_position = 10 letter_6_space = 10 letter_6_height = 5 Loop_y_position =...

:-) Print Settings Infill: 20% Layer: 0,2mm Supports: no Rafts: no Nozzle: 200°C Bed: 60°C I like to use the following tape on my CR-10: http://amzn.to/2zXjJGu This stuff is really great, no extra glue needed, 100% sticky to the printed parts, which...