tbs caipirinha 2 3d models
935433 3d models found related to tbs caipirinha 2.thingiverse
this is a template set for tbs caipirinha 2 its not perfect needs trimming with a dremel tool but its ok for replacing the broken parts.. i broke mine and had to make new ones .. ...enjoy
thingiverse
Wall mount for the TBS Caipirinha 2. Print it in PLA or ABS. You need two pieces, this one and the other one has to be mirrored in your Slicer. The ring has to be printed in TPU, this is used to protect the piece from the screws. ...
thingiverse
This bumper will replace it perfectly, while increasing considerably the crash resistance of your TBS flying wing. The wooden structure has to be cut according to the bumper's geometry, and then the bumper has to be bonded to the wooden structure...
thingiverse
dji camera mount for the tbs caipirinha 2 i broke of my session mount in a crash so made this to fit there instead .. ...can be mirrored to fit on the other side to but some foam need to be cut away to make it fit
thingiverse
Designed an Air Inlet and Outlet Duct to vent a Caddx Vista mounted in the top bay of a TBS Caipirinha 2. Included in the download is a 20mm conversion plate to mount the Vista in the top bay as well as a simple camera mount as I didn’t like how the...
thingiverse
Simple prop spacer to fit the stock PNP Aeronaut folding prop of the TBS Caipirinha 2. This thing should only increase distance to the wing to reduce noise and risk of a prop strike to the foam. ...Still use the floppy prop stops to avoid the prop...
thingiverse
This is a RadioLink SE100 GPS Cradle for the motor mount on a TBS Caipirinha 2 FPV Wing. Used a Caddx Vista VTX in the bay that would normally house the GPS due to the short camera cable so had to figure out a new spot for the GPS. Designed in...
thingiverse
The TBS caipirinha 2 - VTX bay cover is a cover for the left wing bay of the caipirinha 2. The design was made to hold a TBS unify Pro32. After installing the VTX into the wing this part is used to close the bay while holding the VTX and...
thingiverse
Ive drawn a replacement equipment bay cover for the TBS Caipirinha 2. It is designed to be combined with the pushlock mechanism which can be bought separately: https://www.team-blacksheep.com/products/prod:caipi2_pushlock The version with the...
thingiverse
Support for the Winglet on the TBS Caipirinha 2. How to install it: - Remove the first screw on the winglet - Add some glue (UHU Por or UHU Creative) in the support (just the face touching the foam, NOT IN THE WINGLET HOLE) - Insert the...
thingiverse
I needed a way to mount a Caddx Vista to the TBS Caipirinha 2 so I designed a pod to hold one. It is just a push fit and it will not fall out. You will need to make a hole from the back of the pod through to the wing pod behind it. I used a...
thingiverse
Custom GoPro Hero 7 mount for TBS Caipirinha 2. Since Session 5 is getting old and discontinued we asked TBS to get a piece of the Caipi design. We want to thank them for the help empowering the community. This is the result. A fully integrated and...
thingiverse
Remix of "TBS Caipirinha II Furios F35" - added screw mounts (model not printed now and also not tested)
thingiverse
Remix of a TBS caipirinha 2 vtx bay cover to accomodat a rush fpv tank solo 1.5w vtx
thingiverse
I came up with this mount for the DJI FPV Camera on a TBC Caipirinha 2 FPV Wing. This allow putting the DJI Cam into the sport where the GoPro usually goes. This also allows using the DJI Cam Lens Protector. Mount the cam from the back, then mount...
thingiverse
... on going. ...the tbs servos are $25 a piece.... These are a nice alternative to a good and expensive servo. ... These fit snug in servo bays and hold the servo pretty tight, I'd still use some sort of glue or adhesive to make sure they dont move!
thingiverse
This is a little mounting "tool" for the FPV Antenna TBS Caipirinha 2. Use small M3 screws to joint the printed parts to the antenna cable. ...Put the whole thing with some glue through the wing.
thingiverse
The picture is from the first version that it was shorter, actual size is longer.
thingiverse
Seperated the following thing into laser cuttable pieces: https://www.thingiverse.com/thing:2940380 6mm and 3mm Plywood is needed DXF Files cutted with epilog fusion m2 fits well.
thingiverse
My original wood mount got cracked in a crash so I designed this one. I printed mine in Black ABS with 80% infill for strongness, but less will probably work as well. Fits perfectly nice into the original place. ...Depending on the accuracy of your...
thingiverse
made a unify mount for the left wing of the caipirinha 2
thingiverse
I was looking for a proper way to mount a GoPro Hero 8 to the Team Blacksheep Caipirinha 2 without success, so I tinkered one together. - The mount of Airflo is a great base design - The Hero 8 cage is by EricbFPV - Doorconcept/Latch by...
thingiverse
VTX/RX Abdeckung mit optimierten Kühlschlitzen für den Caipirinha 2. Die Schlitze sind jetzt rellativ mittig zur Aussparung. 1mm Dick. Am besten mit 100% Infill drucken wegen der Hitze vom VTX. ------ VTX/RX cover with optimized cooling slots for...
thingiverse
This is a remix of the bottom grill by skaman82. I removed the LED holder and adjusted the size to the gap measured in my build. ... light-weight PLA: 3.2g TPU: 5.7g
thingiverse
This is a printed hinge that allows the use of the polycarbonate cover after the original hinge tags have broken off the end. Simply print it out and epoxy it to the inside face of the cover. ...The standoff fits inside the 6.5mm hole and the whole...
thingiverse
The GoPro Hero 7 is THE solution: with "Hypersmooth" stabilization enabled, it converts your TBS Caipirinha 2 in a perfect Cinematic Long-Range tool that you will love. But the GoPro Hero 7 can't be installed on the TBS Caipirinha without breaking...