tbs crossfire 3d models
6173 3d models found related to tbs crossfire.grabcad
TBS Crossfire TX module placeholder for integration, not including adapter bayMostly accurate, used calipers
grabcad
TBS crossfire for FPV.Solidworks 2017, STEP, IGS, Parasolid.Hope this helps you out in your CAD design!
thingiverse
TBS Crossfire Nano receiver mounting board. ...It fits a normal 30.5 x 30.5 stack with M3 hardware.
thingiverse
This is simple carry case for your TBS crossfire. Main purpose is to protect the antenna so it won't break. ...Has little extra room for some stuff.
thingiverse
Printable case for retranslator from any 2.4Ghz receiver with PPM support to TBS Crossfire TX module. Buying list: 1. Any 5V BEC. https://bit.ly/2LTe0Lw 2. PLS PIN 2.54 L=18.7-19 https://bit.ly/30w92ID 3. Any receiver of your choice with PPM...
thingiverse
Just a super simple antenna holder I made for the TBS Crossfire Immortal T. Used to hold the crossfire antenna on top of my old Turnigy9X (as it doesn't have an internal module - the top antenna was originally wired to the factory JR module). ...
thingiverse
... Module. Please Visit his Blog: https://blog.seidel-philipp.de/ UPDATE: I wrote with Philipp and now it´s possible to print it from Shapeways. https://www.shapeways.com/product/EDK2RV4N3/tbs-crossfire-microtx-low-profile-for-frsky-x-lite
thingiverse
This TBS Crossfire Module Protector can be mounted on the aluminium bars of FrSky stand that most of us have. Just remove the 3 rods and slide the printed model over the stands. It will be tight fit so glue is not needed. It can be best mounted...
thingiverse
This is a mount that I designed to hold my TBS Crossfire transmitter and a 2s lipo to my Spektrum DX8 . It will probably work on other spektrum radios that have the plastic handle. The clips are separate from the main body and glued on. Also as a...
thingiverse
A simple 30x30 mount for the TBS Crossfire diversity
thingiverse
TBS Crossfire mounts for FPVCrate Stark frame. ...Includes mount for TBS Nano rx and Immortal T.
thingiverse
A full sized TBS crossfire bracket that clips onto the handle of the Spektrum DX9.
thingiverse
A TBS Crossfire Nano mount for a Reptile S800. This mount is designed to be embedded in the left wing (as viewed from the back), 14mm from the centre section. ...The lid is removable for access.
cults3d
Lower part for TBS Crossfire Nano TX to fit into new FrSky X20. It works also with Micro TX. Corps Nano v7 is a remix of the normal one with a smaller end of body. ... Pictures are from v7.
thingiverse
TBS crossfire telemetry receiver antenna holder. Keeps antennas 60 degree angle. Print from PLA or similar, Supports required! Slide over antennas and enjoy. ... Print Settings Printer: PrusaMk2 ...
thingiverse
Short and simple design. ... I needed a bed to mount my TBS Crossfire receiver on top of my WalkSnail VTx and came up with this design. Best if printed with TPU, 100% density. ...
thingiverse
A little holder that allows securing a TBS crossfire in place, to prevent getting wet on landings. ...Held in place on the frame using 2 x 20 mm mount points.
myminifactory
TBS crossfire antenna modifications to make it more universal for most frames. Screws in the top plate and has cuttouts for zipties. ...I have moved the antenna up from previous peoples designs to minimize how much of the antenna hangs below the quad.
thingiverse
This is a mount for a TBS Crossfire Nano RX and an FPVCycle Fouride frame if you are using one of the new style AIO boards. In order to elevate the board in the configuration I have it in in the photos, you'll need M2 x 16mm screws and m2 x 8mm...
thingiverse
Designed to provide a secure way to mount an external battery to power the TBS Crossfire. It was designed around a Lumenier 2500mAh 2S lipo battery (www.getfpv.com/lumenier-2500mah-2s-radio-transmitter-lipo-battery.html). Prints in two parts to make...
thingiverse
If you can't print this, please consider ordering it through my 3DHub at: http://3dhubs.com/service/8Bit TBS crossfire antenna modifications to make it more universal for most frames. Screws in the top plate and has cuttouts for zipties. I have moved...
cults3d
I designed this tube to transform a normal TBS Crossfire Micro antenna into an Immortal T. Things needed for the build: - T printed in TPU - micro antenna - two 3mm tubes need tabout 80mm and 72mm in lenght. - a zip tie To assembly the Immortal, the...
thingiverse
I designed this tube to transform a normal TBS Crossfire Micro antenna into an Immortal T. Things needed for the build: - T printed in TPU - micro antenna - two 3mm tubes need tabout 80mm and 72mm in lenght. - a zip tie To assembly the...