tbs source one gopro mount 3d models

I designed a sturdy mount specifically to safeguard the antennas from damage caused by propellers. ...This solution effectively clears 2.5-inch props, ensuring reliable operation and performance.

... screws, and a Lumenier Axii Stubby Antenna. ...A designated slot at the bottom enables main power wires to be easily routed outward. The XT60 pigtail is subsequently fastened to the mount with a zip tie to prevent it from interfering with propellers.

This is my version of bumpers for TBS Source One HD (and also V4). The parts have tolerance so that should easily fit once printed. ... VTX mount is for V3 is larger than the on for HD version

Mount for my naked Blackview Hero 1 for TBS Source One V4/HD 3 extruded points get into holes of camera to block it in place. ... Compatible with dedicated naked mod for Blackview Hero 1 (my other design)

Mount for my naked Blackview Hero 1 for TBS Source One V4/HD 3 extruded points get into holes of camera to block it in place. ... Compatible with dedicated naked mod for Blackview Hero 1 (my other design)

The mount allows the TBS Source One to be stacked directly on top of the flight controller unit, streamlining setup and increasing overall system stability. ... The VTX unit is positioned off-center to accommodate the short SMA cable, ensuring a secure...

Needed some more space for a 30x30 vtx in my new TBS Source One V3 With this part I was able to mount another 30x30 stack in the back/rear section of the TBS Source One v3. I printed the part in TPU, the holes for the post are slightly smaller so...

TBS Source One V4 - XT60 and GPS holder for the BN-220T gps with SMA adapter hole. ... Thanks to MadVulture for his great initial design for the TBS Source One V3 frame. ...

3D printing parts custom made for the TBS Source One V4 Frame. ... Cambumper made for Caddx Vista Nebula nano Backbumper made for Caddx Vista + Caddx Vista Antenna + TBS Imortal Antenna Skidz can be sued with any build Bottom Bumper can be made for any...

My parts to mount a DJI FPV Air Unit into a TBS Source One V3. I designed this already yeas ago but forgot to upload. So now in case you still use a V3 frame and a full air unit. This will allow you to mount it all. It is designed with with...

This is a Slider you can Put on the arms of your tbs source one (designed for V4) Frame. Is protects the under side and looks sick as hell. ...Have fun with it!

TBS Source One - Armguard and Skidz. Send me a message if you need this altered or something different entirely. I love creating custom quad parts, remixes, and prints. ...You can find me on Instagram @FlyHighFPV or youtube.com/FlyHighFPVdrone

Bumpers to fit around the end of the TBS Source One v4 arms. ...Printed in TPU these have a snug fit around the end of the arm, and holes for the motor bolts.

I did create an 2.4gHz ELRS antenna support for TBS Source One V5 frame. ...Print Settings Printer: Artillery Genius Rafts: No Supports: Yes Resolution: 0.2 Infill: 20 Filament: Any TPU Any Category: Hobby

This is a specially designed battery pad tailored to fit the TBS Source One v.02 drone perfectly. ...Strategically crafted notches ensure that battery straps are aligned precisely with the battery, creating a seamless and secure connection.

This arm protector is designed for the *5-Inch* version of the TBS Source One. The 3MF file is set up for four pieces with PrusaSlicer settings for TPU. ... For easy remixing, I've included the F3D file.

This is a pigtail holder for the TBS Source one V5. It needs to be printed in TPU for its flexibility. ...It is designed so you can run the battery lead out the back.

This is a Arm Guard for zhe TBS Source One V5. It needs to be printed in TPU for flexibility. ...The good thing about this design is, that it holds itself to the arm without the need to screw it.

A simple camera tilt mechanism for TBS source one V5 with a smallest servo i could find. ... It is designed for Foxeer Night Cat 3 Micro camera, but should work with other similar sized cameras

TBS Source One v3 DJI FPV mounts feature an antenna mount, Airunit mount, and an arm bumper/skid combo. To fit the Airunit in the back, remove the back standoffs. If you're feeling adventurous, drill out the top plate to move the standoffs just a...

... can be attached to the rear mount as well. Camera Mount https://www.thingiverse.com/thing:3847521 Gopro Mount https://www.thingiverse.com/thing:4050847 Bumper https://www.thingiverse.com/thing:4012109 Feet https://www.thingiverse.com/thing:4540053

A VTX lollipop antenna holder made for the miniquad frame "Source Two" by TBS. Should work with "Source One" too. ...It's made for antennas that directly connect to the VTX, with a 1.8mm thick cable and a u.FL connector.

For my first Drone built, I went for a new TBS source One V5 frame. There is not a lot of 3D part for this frame so far, so here are my arms protection and skid, that are also used for motor soft mount. ... Print in TPU, 0.2mm layer height,...

Mount for a TBS Source One V5 to use a Micro AXii 2 antenna and Happymodel EP1 antenna. ...Other receiver antennas may fit as well https://youtu.be/Y0Gkqp5ILKs I printed mine laying on it's back with the antenna parts on the top pointing up

## TBS Source One v4 Better Skids / Arm Bumpers After creating this kind of skid for a few different frames, I wanted it also for the TBS Source One v4. Its a heavy duty bumper designed for concrete and road flying and sliding. Put on and forget....

Build: 20x20 stack, caddx vista polar with SMA antena + mount for Tmortal antena TBS CRSF

A quick and dirty 30min remix for a Hero 8 on a tbs Source one V5. I just needed something short term till I have more time, or better designs become available. Holds a camera butter ND filter and is not hot garbage like far too many fpv mounts on...

This is my version of bumpers for TBS Source One HD (and also V4). ...The parts have tolerance so that should easily fit once printed.

These are TPU arm/motor guards with soft mounting for the 7” TBS Source One quadcopter drone. NOTICE: These guards fit only the 6mm thick version of the 7” arms, specifically designed for V0.2 arms with larger tips. They will not work with V0.1...

This is a Chin Bumper for the TBS Source One V4 Frame. It's designed to protect the bottom carbon Plate from frontal crashes. ...Use M3 Screws as shown in the Pictures to attach it to your fav drone and don't forget to have fun and enjoy flying ;) Rip...