tbs source one gopro mount 3d models

<p>I needed a way to attach a battery strap with out going under the carbon, since the add-ons I designed prevented this. ...This solution solved my issue.</p> <p>Print in TPU only.</p> <h3>Print instructions</h3><h3>Category: R/C Vehicles Print...

<p>This design has a "lip" thing to prevent dirt from going in the motor. ...Motor bell used was 28mm diameter.</p> <p>You'll have to force it in but it's not too bad, and it's a tight fit after :)</p> <p>You can also scale it 1 or 2% bigger in your...

I'm initiating the motor safeguard protocol using the TPU shielding technology, specifically designed to safeguard motors from damage caused by physical impacts. ...The protective feet of the TPU are strategically placed around the motor to absorb and...

I utilized the TPU to produce a physical copy of this document.

use m3x8 screws and a zip tie to hold the antenna

Trying to save a few grams on my build. I always print these at 100% infill. 5mm is for just arm protection, saves about 4 grams total. 8mm is for doing slides, saves about 8 grams total. ... Not a big savings but it adds up.

I created this for those times when I want to soar over water. Normally, I pull out the electrical tape and wrap it extensively, which is painful since every time I need to change the battery I have to re-tape it all over again. With this setup, I...

I required a method to affix a battery strap without slipping beneath the carbon layer, as my customizations obstructed this area. ...This solution effectively addressed my problem.

This design has a "lip" thing to prevent dirt from going in the motor. Motor bell used was 28mm diameter. You'll have to force it in but it's not too bad, and it's a tight fit after :) You can also scale it 1 or 2% bigger in your slicer software if...

Please enjoy my keychain. Thanks a lot. 3 versions: 1) Finger Edition! 2) Featuring a 4mm design with our company name in a small print. 3) Showcasing a 3mm design with our company logo prominently displayed in larger text. ... JuampiFPV.com

FPV pilots need a sturdy front bumper to shield their cameras from damage. A flexible material is perfect for this application, as it can absorb impacts without compromising the integrity of the system. ...The latest design, version 2, has been...

It's just 2 little top plate front bumpers to avoid you destroying your top plate when you crash (yes, it happened to me, twice) I'm printing them in PLA but it should work fine with TPU as well.

Simply slide these onto your standoffs and you're good to go. ...There's a few different versions in here to work with some parts I had (Speedybee F405 V3 FC and ELRS RP3 Nano Reveiver Antennas) so your mileage may vary.Boolean out your own holes from...

My modification to the Source One Cam Plate. I got tired if the cheap camera adapters that seem to shatter on heavy impacts. ...I designed this around the dji camera but it should fit most mini cams that are around 20mm wide.

Open Source Pen project. Contains 2 caps for 125mm and 134mm pen rods. Can be used if the original pen body is damaged to give the second life to the remaining pen rod. ... Assembly: - Insert Pen Rod into the Pen Body - Insert the Cap into the...

Thanks TBS for making this frame open source. This is a lil arm protector for the TBS Source PodRacer. If you, like me, fly over concrete, you might want to print some of these. You can either put it on top of the arm and have it also work as a soft...

Simple bumper for TBS Source One V5

Alien 5" GoPro Mount 20° with support for TBS ND Filters. ... The design is open-source and available here: https://www.tinkercad.com/things/31f5D6pEZcv Design inspired by: https://www.thingiverse.com/thing:3188260

GoPro Mount for the Armattan Rooster - Inserting a TBS Jellyproof ND Filter

TBS ND Filter Mount for Nameless RC Naked GoPro Hero 9 10 Case

30-Degree GoPro Mount Featuring Built-in TBS ND Filter Slot

File Info GoPro Hero 5/6/7 Action Cam Mount for the SourceTwo Frame Print it in TPU! I recommend SainSmart TPU! Support Me If you like my free designs and want to support me and my FPV Blog: Patreon Buy me a Beer on Thingiverse ("tip designer" on...

... fins with a sleek mount designed by Chriviper. ...I adapted it to pair perfectly with the TBS Unify Pro SMA mount featuring its two small mounting holes. ...The result is essentially a press fit, securing tightly without needing any screws in place.

### Support Me If you enjoy my free designs and want to support me and my FPV Blog: - [Patreon](https://www.patreon.com/philippseidel) - [Buy me a Beer on Thingiverse](https://www.thingiverse.com/ps915/designs) ("tip designer" on the left) - or...

I designed this protective housing to safeguard the motor wires on my high-performance TBS Source Two racing quad.

The Micro Frame TBS source requires custom arm protection to safeguard against damage during transportation and handling.

This is canopy for: TBS Source Two frame Micro camera with big lens VTX antenna foxeer lolipop 3 Compact version of stack

TPU Mount with GoPro mount for TBS GPS M8-2 on GepRC MARK 5 FPV quad Video: https://www.youtube.com/channel/UCcJWLBfacedY6TE3ikykgQw

Variable camera angle for the TBS Source V frame (45-85deg) Aero canopy/flip fin with holes to accomodate an antenna. ... Support is recommended but not needed for the canopy,