tbs source one 3d models

Same as item remixed from but with a 0.2mm (1 layer height) square added over the holes. This allows for full side to side bridging with other features printed above. screws will just poke through the very thin extra layer. Can be printed without...

Just a very simple adapter to reduce the holes in the frame for the Vista to m2. I used a small nylon nut to hold the screw in place. ...In this way, the Vista is also isolated from the frame, protecting it from a short circuit on the frame, for...

A tiny bracket is needed to secure an R-XSR to the rear standoffs. ...Wrap a compact cable tie around the hole, then seal it with heatshrink tubing as you connect the antenna.

Remixed so that it fits normal (non-TSB) SMA pigtails, without the two holes on the side. ... GPS module is a BN-220.

Designed this soft mount to reduce the motor vibration transfer to main body. Print of very soft tpu and install to both sides of arms. You need 6mm longer stack and arm attachment screws to assemble this. Remember to use loctite! ...

I've built a fantastic TPU Hero 4 mount all by myself. ...I hope you'll have a blast using it, and who knows, maybe you'll even make some amazing videos with it!

I needed a more substantial base for the S1, so I reworked several concepts to create something more robust. The main frame is constructed with TPU for added durability. ...The mount's angle is set at a precise 30 degrees.

TPU: Print with 1-2 Wall thicknesses for good damping. ... On the outside of the arm it is slightly thicker for better protection.

Shims print in TPU you will need M2x8mm screws

Fairly messy model but it prints well and has survived a few crashes. ...I couldn't get other models to fit properly, so made my own.Printed at 100% infill, requires an M5 nut for the GoPro Screw.

I printed B0bafart's great model but had some issues that I then changed: -made the standoff mounts wider to prevent the rings from separating - made the hole for the antenna lead large enough to fit the U.FL connector (might still need to...

Print in TPU, add a large m3 screw and nut (washers are nice to have)

A rough hack to repurpose RX holders as a VTX antenna mount for axii-style antennas, perfect for those who need a DIY solution. Thanks for sharing this tip, Max! ... - Flakes

I heard you guys like AXII mounts. I've designed this to work with a MCXX AXII antenna. Along with it tube mounts for RF antennas at a 25 degree spread and 15 degree up tilt. Print in TPU 50-70% infill at .016 layer or less. I also added...

Quick model based on SourceOne V4 top plate

Cover/protection for the wire of the motors in a 5 inch quad. ... Printed in PLA

Really strong shell for this thin camera, perfect for hard uses like bandos. To insert the cam you need to cut the shell on the left side, then glue it with super glue and you are ready to rock. Tilt is 28 degrees The monkey edition has...

A cutting-edge, high-tech action camera mount designed to capture breathtaking footage at a precisely calibrated 28-degree angle, engineered with precision and innovation to achieve maximum stability while minimizing unnecessary bulk.

little, portable ELRS antena holder, works great very durable, i also upload caddx vista antena holder which combines these two parts very well. ... enjoy :)

This remix covers the top of the arms and has skids below. ... The following files were used for the remix: https://www.thingiverse.com/thing:3176233 https://www.thingiverse.com/thing:3552335

Since there are still very few frames for the DJI O3 Air Unit, we decided to make something ourselves. The TPU parts have been printed by myself with Sainsmart TPU on an Anycubic Mega X using Simplify3D as slicer. Unfortunately we had no...

Quad Bumpers for Everyone: Three Simple Designs to Suit Your Style. Get ready to take your quad bumping game to the next level with these three super simple bumper designs that cater to all your needs! **Thicc Bumper: The Ultimate Protector** Take...

Keeps the video antenna in place and leaves some room for the XT60 pigtail. ...The hole for the SMA connector might need some sanding depending on your print settings.

I wanted to support the FPV camera using TPU so that the camera housing doesn't crack during crashes. As a bonus, this weighs less than the original carbon fiber plates as well. ... Print in TPU, vertically.

Receiver and VTX Antenna Mount Now Available in SMA Version.

I've only tried this type of material and resolution but there shouldn't be any problems with other materials.

Yes its for free <3

https://www.youtube.com/watch?v=MN_E6dyI8hU&feature=youtu.be No more frame on the view Lighter than full size cam More place inside build To be used with bumper