tbs source one 3d models

... your most robust filament. Upper parts should be printed in TPU but also work in other materials. Default Iflight Hole Spacing 25x36, Source one 24x40 for other quads, Angles or Gopros, just comment the hole spacings and I'll see what I can do!

:-)** DJI O3 and Source One v4. It requires 4x M1.6 10mm phillips screws for the VTX and 4x M3 6mm bolts and nuts to secure the mount to the frame. The matching camera mount is here: https://www.thingiverse.com/thing:5687561 Print in TPU in...

A straightforward Solution to pair with the Source camera. ...I'm pleased with how it's turned out, about 9 out of 10 would be my rating.

Had no options but to make my own

Direct antenna support for VTX right, enabling a straightforward VTX-to-antenna placement. ...Adding hot glue can ideally reinforce and insulate the setup.

Designed for a foxeer pagoda pro. Notch is to slot the flexible sheilded body in and then pull it flush. ...The flat side of the plate in the mount should face inside the body.

Print in tpu with supports

Narrower spring and high dampening gopro soft mount. 25 degree camera angle. Remixed to work better with reelsteady. The original part was too stiff, the spring was too short, and transferred too much vibration into the camera. As of 11/18/20, I...

Stand at the forefront of DJI's aerial innovation within a singular frame of reference.

Remix of the oldmancolin mount - I just removed rx antenna mount from it so the XT60 can be easily routed there.

TPU

I utilized the mini camera mounting device and OpenSCAD software to accomplish this task.

30 deg mount for Xiaomi Yi 4k.

We've incorporated a versatile rear-facing 19x19mm camera mount, perfect for enthusiasts of cheat codes. ...Additionally, a discreet tube runs along the back of the mount, cleverly concealing wiring for an enhanced aesthetic appeal.

its a clear plate for anyone to put anything on.

Mounting reinforcement was added to the Matek GPS holder, the label was completely removed from it, and a rectangular opening was carefully cut into the top section for improved satellite signal accessibility.

Mount for the DJI Air Unit Stock antennas. ...Air unit placed on the bottomplate in the back of the Quad while leaving out the standoffs.

Short Antenna Mount with a hex in the inner, so the Pigtail couldn´t rotation while Antenna Screw.

A pad, giving you the possibility to mount a battery on the bottom. Its attached with the screws of the standoffs through the holes. ... Print, mount and add a sticky lipo pad to it.

Here is a rewritten version of the text: "Due to special request, I've taken this design even further. It's perfect for a micro cam setup. To make mounting easier, I left some extra material around the holes, and I highly recommend adding a washer...

I decided to move the mount up and back a bit to get it in tighter proximity to the frame. ...This adjustment allowed me to position the mount exactly where I wanted it, resulting in a more balanced composition.

Good coverage for aO3 Antenna in hard crashes. ...Get Fill at 100% for maximum protection.

End Caps for Open V-Slot 2020 with Open Hardware logo. ... This is a remix from https://www.thingiverse.com/thing:398515

This is a base model for BMC3D's freestyle hero mount, created to serve as a foundation for a custom hero mount already in my possession.

A basic micro cam mount is available for those who prefer to go without a chin guard. For added protection and stability, we recommend using the chin mount version that comes equipped with a durable chin guard. ...Enjoy your improved recording...

35 degree tilt

Small antenna mount for the back of the frame. Only VTX antenna, no RX antenna or GPS. Angled at 55 degrees. ...Made for the CaddxFPV antenna for Vista, but works with other similar sized antennas as well (~3.80 mm diameter pole).If printing with hard...

I've revised the design to address the concern about the proximity of the legs on the previous model. ...The new version has a wider stance, which should provide improved stability and balance.