tbs unify pro hv 3d models

This is a mount I designed for the TBS Unify Pro HV with it's pigtail to be able to mount it in a wing or fuselage. This is a 2 part mount, the base gets cut and glued into the required place, and then the mount fits into the base from the top. It...

Halterung für die FPV Antenne am Lisam 210. ...Für TBS Unify Pro Hv Print Settings Printer: Sparkcube Touch! Rafts: No Supports: No Resolution: 0,2 Infill: 45 Notes: Halterung für die FPV Antenne am Lisam 210 für TBS Unify Pro HV

I was inspired by this stack mount. ... https://www.thingiverse.com/thing:1569752 This one is for the TBS Unify Pro HV Race. You'll need a flexible Material like TPU for it. ...

This is a side mounted vtx plate, allows you to attach any vtx really but this one was made with the Tbs Unify pro hv in mind. Allows you to turn it on in pit mode without a hassle and to change channels easily Its a snug fit to nylon standoffs, to...

I remixed this from a similar part I found that was designed to hold the Team BlackSheep Unify Pro HV and add some structural support...

Pictures are of the Unify Pro HV mount since that's all I had at the time, but the other mounts have been tested and work the same way. Print Settings Printer: Prusa i3 MK2 ...

Mount for TBS Unify Pro HV Video Transmitter for Martian II 220 frame. ... Print with TPU.

Sourceone v0.2 TBS Unify Pro HV ViFly v2 Capacitor 35v 1000µF Rubycon Dia 12.5

SImple stack mount/holder for TBS Unify Pro HV Racing Edition v2.0

Off center mount for a TBS Unifiy Pro HV

Off center mount for a TBS Unifiy Pro HV

Standoff Mount for TBS Unify Pro. 30mm spacing between center holes of stand offs. ...Designed to fit the MRM Scythe 220.

... the Impulserc Alien 5". ...It holds the antenna pigtail for the TBS Unify Pro HV VTX. As well it mounts the antenna tubes for your RX. ... Print Settings Printer: Creator pro Rafts: No Supports: No Resolution: .2 Infill: 100% Notes: Print upside down.

TBS Unify pro HV mount with FC or 4in1 esc stack. Placing it in the stack give it the cleanest of all the trial designs I thought up. Notes: Best printed in ABS or high temp filament due to VTX temps 1. There is a small front to rear offset. ...

TBS Unify Pro HV mount for 30x30 stack

Direct replacement for OE Rear Standoff to support a TBS Unify Pro HV VTx antenna and Rx antenna mounting

Changed the layout compared to Vasos remix a bit. ... Added mount for R-XSR directly on the lid Changed supported VTX to a TBS Unify Pro HV Race 2 Support for antenna tubes maintained

Mount specifically designed to fit 30.5x30.5 internal stack to hold TBS Unify Pro HV and an XM+ receiver. ... Printed in TPU for flexibility to squeeze the Unify and XM+ into it but tough enough to hold things in place very well.

This is a rear lid for the ZOHD Dart 250.It fits an FrSky R-XSR and a TBS Unify Pro HV Race 2 including the corresponding antennas.With the heatsink of the VTX in the airflow it should not be able to overheat.

These 2 minimalistic pieces help mounting a TBS Unify Pro HV / Race to a 36 x 36mm size flight controller (BF F3, Naze32,...) They're meant to be printed in a flexible material (ideally in TPU) Note: These pieces probably won't work for the 5V...

I made a three-piece design to snuggly accommodate R9MM, TBS Unify Pro HV and ImmortalT antenna in the back of Armattan Chameleon Ti 5". Print layed as on pictures, ImmortalT requires support from the bed only; TBS Unify & R9MM mount with normal...

TBS Unify Pro 5G8 HV Race 25/200mW Video Transmitter

Nazgul5 v2 TBS UNIFY PRO 5G8 HV holder

Quick design to hold a TBS Unify Pro HV Race. ...Used in my Martian 2 quadcopter but probably could work with anything that's not too tight.

Super G Plus TBS VTX Unify Pro HV mount that gets held by two standoffs.

It´s a Remix of Mr.Anderson6655 perfect Mount for the Unify HV Version with screws and i made it for Wings

This thing is a 2grs VTX mount for TBS Unify 5G8 HV on a 30x30 stack

Modified to fit TBS UNIFY PRO 5G8 HV VTX. ... Check this it you need complete Chameleon Ti rear end: https://www.thingiverse.com/thing:3654907

A basic mount/holder for the TBS Unify HV video transmitter. I made it without a bottom so that air can circulate more freely. Designed for my specific build, there is a cutout for the SMA cable when it has been doubled back on the other side...

VTX holder that is to be installed on the rear standoffs. Just use a tie-wrap to hold the VTX in place. I made a version in 2 parts because it's a support nightmare otherwise. For those who have the right tools there also is a 1 part version. The...