tbs unify pro hv race 3d models
96584 3d models found related to tbs unify pro hv race.thingiverse
I was inspired by this stack mount. ... https://www.thingiverse.com/thing:1569752 This one is for the TBS Unify Pro HV Race. You'll need a flexible Material like TPU for it. ...
thingiverse
Changed the layout compared to Vasos remix a bit. ... Added mount for R-XSR directly on the lid Changed supported VTX to a TBS Unify Pro HV Race 2 Support for antenna tubes maintained
prusaprinters
This is a rear lid for the ZOHD Dart 250.It fits an FrSky R-XSR and a TBS Unify Pro HV Race 2 including the corresponding antennas.With the heatsink of the VTX in the airflow it should not be able to overheat.
thingiverse
These 2 minimalistic pieces help mounting a TBS Unify Pro HV / Race to a 36 x 36mm size flight controller (BF F3, Naze32,...) They're meant to be printed in a flexible material (ideally in TPU) Note: These pieces probably won't work for the 5V...
grabcad
TBS Unify Pro 5G8 HV Race 25/200mW Video Transmitter
thingiverse
Quick design to hold a TBS Unify Pro HV Race. ...Used in my Martian 2 quadcopter but probably could work with anything that's not too tight.
thingiverse
SImple stack mount/holder for TBS Unify Pro HV Racing Edition v2.0
thingiverse
I took these perfect unify pro holder (http://www.thingiverse.com/thing:1706954) and customize it for the RunCam SWIFT MICRO. Its perfect for the Redux130 from flyduino. ... You can buy the cam here: ...
thingiverse
Print Settings Printer Brand: PowerSpec Printer: PowerSpec 3D Pro Rafts: No Supports: No Resolution: .20 Infill: 100% Notes: Designed to be printed with TPU. ... I also have another version available without the antenna mount if anyone is interested,...
thingiverse
Just my design of a VTX Mount for the Unify Pro HV Race on the TBS Source One Quad.
thingiverse
ZMR250 mount for TBS Unify Pro HV & TBS Unify Pro HV Race pigtale
thingiverse
... 2 HD Camera with antenna holders. ...Front plate for the Runcam Swift 2 that gives a 30 degree camera angle. Back holder for an antenna (tested with TBS Unify Pro HV Race Edition). ...Used Ninjaflex for the Runcam 2 Holder and ABS for everything else.
thingiverse
J'ai crée ce spacer pour mon vega supra afin d'isolé mon vtx TBS unify pro HV race 2. j'avais des interférences avec mon RX placé juste au dessus. ... Problème résolu grâce a ce spacer.
thingiverse
Fits for these Frames: LX4 https://www.gearbest.com/brushless-fpv-racer/pp_626362.html?lkid=11419735 LX5 https://www.gearbest.com/brushless-fpv-racer/pp_626361.html?lkid=11419735 LX6 https://www.gearbest.com/racing-frame/pp_626365.html?lkid=11419735...
thingiverse
I remixed this from a similar part I found that was designed to hold the Team BlackSheep Unify Pro HV and add some structural support...
thingiverse
This is a mount I designed for the TBS Unify Pro HV with it's pigtail to be able to mount it in a wing or fuselage. This is a 2 part mount, the base gets cut and glued into the required place, and then the mount fits into the base from the top. It...
thingiverse
Pictures are of the Unify Pro HV mount since that's all I had at the time, but the other mounts have been tested and work the same way. Print Settings Printer: Prusa i3 MK2 ...
thingiverse
Holder for TBS UNIFY PRO 5G8 HV - RACE 2 (MMCX) and FRSKY receivers (in my case - XM+). There is a hole at the bottom for the TBS TX wires. ... Distance between holes is 30.5mm
thingiverse
Halterung für die FPV Antenne am Lisam 210. ...Für TBS Unify Pro Hv Print Settings Printer: Sparkcube Touch! Rafts: No Supports: No Resolution: 0,2 Infill: 45 Notes: Halterung für die FPV Antenne am Lisam 210 für TBS Unify Pro HV
thingiverse
This thing is a 2grs VTX mount for TBS Unify 5G8 HV on a 30x30 stack
thingiverse
Standoff Mount for TBS Unify Pro. 30mm spacing between center holes of stand offs. ...Designed to fit the MRM Scythe 220.
thingiverse
This is a side mounted vtx plate, allows you to attach any vtx really but this one was made with the Tbs Unify pro hv in mind. Allows you to turn it on in pit mode without a hassle and to change channels easily Its a snug fit to nylon standoffs, to...
thingiverse
A basic mount/holder for the TBS Unify HV video transmitter. I made it without a bottom so that air can circulate more freely. Designed for my specific build, there is a cutout for the SMA cable when it has been doubled back on the other side...
thingiverse
It´s a Remix of Mr.Anderson6655 perfect Mount for the Unify HV Version with screws and i made it for Wings
thingiverse
This is my first published designe on thingiverse. ... Its a 35mm Stack mount for the TBS Unify HV Race V2. ... Material: TPU V4: Re-Scale
thingiverse
... for the TBS SOURCE V frame. ... Support for FOXXER PREDATOR MICRO with fixed inclination of 50 °, support for FOXXER LOLLIPOP 2, anti-tip fin with guide holes for antennas, support for VTX TBS UNIFY PRO 5G8 HV - RACE 2 (MMCX) + FrSky R-XSR Receiver.