tbs unify race 3d models
27481 3d models found related to tbs unify race.thingiverse
I´m using this mount to secure the unify race fpv transmitter to the inside top plate of my frames. The unify is held in place with a zip tie around the mount and the mount itself is mounted via double sided sticky tape to the carbon. It´s possible...
thingiverse
I needed a TBS Unify Race 2 Mount for my racer, so i designed one. ... 30.5x30.5 Stack Maybe someone needs it too.
thingiverse
TBS Unify Race and FrSky XSR dual mount. Print in TPU, no supports. Fits nicely on top of your FC stack New! ... R-XSR mount added
prusaprinters
TBS Unify Race and FrSky XSR dual mount. Print in TPU, no supports. Fits nicely on top of your FC stack</p> <p>New! ...R-XSR mount added</p> <h3>Print Settings</h3> <p><strong>Printer Brand:</strong></p> <p>Prusa</p> <p class="detail-setting...
thingiverse
This is my first published designe on thingiverse. ... Its a 35mm Stack mount for the TBS Unify HV Race V2. ... Material: TPU V4: Re-Scale
thingiverse
Imprimir con TPU al 100% de relleno y con soportes.
thingiverse
... 2 HD Camera with antenna holders. ...Front plate for the Runcam Swift 2 that gives a 30 degree camera angle. Back holder for an antenna (tested with TBS Unify Pro HV Race Edition). ...Used Ninjaflex for the Runcam 2 Holder and ABS for everything else.
thingiverse
Hello Guys, this is my selvemade holder for the unify and the flydunino mini OSD. ... Print Settings Printer Brand: Ultimaker Printer: ...
thingiverse
Bracket for iFlight iX5 V2 5 inch 210mm and TBS Unify Pro Race VTX SMA Layer height 0.1 Infill 60% Standoff holes are a tight fit, bore out to the fit required. ... Enjoy.
thingiverse
2 Part Case For TBS Unify Pro Race Video Transmitter, Hole spacing of 30.5mm to fit on flight controller stack. ... Pass through for push button on top of case.
thingiverse
I was inspired by this stack mount. ... https://www.thingiverse.com/thing:1569752 This one is for the TBS Unify Pro HV Race. You'll need a flexible Material like TPU for it. ...
thingiverse
SImple stack mount/holder for TBS Unify Pro HV Racing Edition v2.0
grabcad
TBS Unify Pro 5G8 HV Race 25/200mW Video Transmitter
thingiverse
Quick design to hold a TBS Unify Pro HV Race. ...Used in my Martian 2 quadcopter but probably could work with anything that's not too tight.
thingiverse
Changed the layout compared to Vasos remix a bit. ... Added mount for R-XSR directly on the lid Changed supported VTX to a TBS Unify Pro HV Race 2 Support for antenna tubes maintained
thingiverse
These 2 minimalistic pieces help mounting a TBS Unify Pro HV / Race to a 36 x 36mm size flight controller (BF F3, Naze32,...) They're meant to be printed in a flexible material (ideally in TPU) Note: These pieces probably won't work for the 5V...
thingiverse
Just my design of a VTX Mount for the Unify Pro HV Race on the TBS Source One Quad.
prusaprinters
This is a rear lid for the ZOHD Dart 250.It fits an FrSky R-XSR and a TBS Unify Pro HV Race 2 including the corresponding antennas.With the heatsink of the VTX in the airflow it should not be able to overheat.
thingiverse
I took these perfect unify pro holder (http://www.thingiverse.com/thing:1706954) and customize it for the RunCam SWIFT MICRO. Its perfect for the Redux130 from flyduino. ... You can buy the cam here: ...
thingiverse
This is a VTX pigtail holder for a TBS Unify on a Strix Screech R V2 frame. It is designed to hold the pigtail in between the two back spacers. It is a very very tight fit with PLA, it should work alot better with flexible material like TPU. ...
thingiverse
Modeled in OpenSCAD. Printed in TPU at 100% infill. The VTX fits in snug with no movement during flight. There are holes on each side for a cable tie to secure the VTX is you'd like. Any questions or suggestions, please contact me. Print Settings...
thingiverse
I made a sma antenna mount for the floss 3.0 to accept the xf race antenna edit 4-23 Tyler of tinyleds.com asked me to made this new version to accept his flipstick turtle / quopa mode aid. ...its a very ridgid 4.75mm rod that is streamline and works...
thingiverse
This is a mount for Marmotte to secure the TBS Unify Race 2 VTX, Frsky R9 Mini RX and Immortal-T antenna in place. ...Print with TPU 95A or 98A to have enough solid mount, but flexible enough to fit the antenna.
thingiverse
This is a mount for TBS Unify Race 2 VTX and Frsky XM+ receiver. It mounts to 20x20mm stack with M3 screws. M2 might work as well. ... Mount includes holes for 2,5x1 size zip ties to secure the VTX and XM+ in place
thingiverse
TBS unify Holder for Frame Martian 220 5’’ - https://goo.gl/GUpaVz TBS unify (pro,race... ...) - https://goo.gl/S9LZnD Complete Stuff of quad : Frame Martian 2 220 5’’ - https://goo.gl/GUpaVz Motor Racerstar 2205 2300kv - https://goo.gl/oDGH5i ESC...
thingiverse
3 Versions of Universal Mount for TBS Unify Pro. ...Print Settings Rafts: No Supports: No ...
thingiverse
TBS Unify Pro32 Cradle for a generic quad frame. VTX should just click in. There is also a version of the bracket that includes a compositor holder. ... Was printed with PTFE
thingiverse
I designed this mount to attach the TBS Unify EVO sender to my F550. The sender is fixed by two metric screws and the mount itself was glued to the F550 body. ...