telescope with nikon mount 3d models
2866108 3d models found related to telescope with nikon mount.thingiverse
... of the adapter. ... I have added (M28.5x0.6) threads to mount light filters in the Nikon adapter, mixing the following: https://www.thingiverse.com/thing:237376 https://www.thingiverse.com/thing:4689425 Print with 0.1 layer hight for good results
thingiverse
Wanted a version that could mount my old F Mount Nikon Camera to my Meade Telescope. ...
thingiverse
"1 Nikon" .stl file is the printed object, WITHOUT the ring "stopper" (for an easy mounting for the metal ring) and worse grip ring (for my printer). "2 Nikon" .stl file is the "NEW" version of this adapter, the "grip ring" has less bar (80 instead...
thingiverse
An adapter to attach my Nikon DSLR to my Celestron 6se telescope The thread at the end that connects to the telescope is 2"-24. The thread to connect the camera part to the telescope part is M45x1. This is not a standard thread for telescope...
grabcad
C11 11in Cassegrain optical tube, inspired by the C11 tube from Celestron Mount : G11 from Losmandy, a strong robust and very practical mounts, probably the best I teted so far for that weight category. Apogee ALTA as imaging camera ... ...from the time...
prusaprinters
This is a remix of Nikon to Telescope Adapter 1.25" by Carsten, but with a 20mm longer barrel for telescopes that need a bit more length to get in focus.
thingiverse
Fit 1.25" telescope eyepieces Instructions Keep the layer height low (0.1), and it will print just fine with the big end sticking up. ... No support material required.
prusaprinters
... of the low tolerances in the bayonet part, It's best to print that part at at most 0.15mm layer height, avoiding rounding errors. Cura does this just fine with "adaptive layers" and for instance a layer height of 0.175 with 0.025 maximum variation.
thingiverse
Adapter to attach a Nikon camera to a focuser for prime focus photography. ... Unlike the example in the photo, you might want to print this in a matte black material to avoid reflections.
thingiverse
Big Battery mount for a Tracer 12V 22Ah A few bins to hold stuff (Flashlight, cables, etc) A bigger bin A 3 lens holder (1.25in lens) I added a base that will prevent it from spinning (Fits the Celestron Evolution 8 tripod). I've included the...
grabcad
simple large GEM mount using 3 inch shafts. Add your drive system and telescopeCurrently set for 47 degrees North. Change slot to allow for other latitudes. ...Still needs a jack screw for the wedge.
thingiverse
... laser holder is the same as in the original design, but I added 6 screw caps suitable for M4 screws. With these caps you will avoid damaging your laser with the screw ends while still being able to tight it firmly. I prints without support. ...
thingiverse
I needed to attach my Nikon Z6 camera to my telescope, but did not find any adapters on the market - so I made one :) This one can either be put directly into a T2 telescope, or as I do attached to a flat-field corrector - in my case for my F4...
thingiverse
Using LordFly's mount, I sliced that section off to make a mount for my older telescope. 0.965" mounts are obsolete, but some of us still have these telescopes kicking around. This print fits perfectly, and is best printed with the small section...
thingiverse
While an astronomy camera will work, a Nikon 1, being as cheap as they are (and with their new mirrorless design seemingly abandoned.) This would provide a nice contained and mobile solution. I started printing out the original, but it jammed,...
thingiverse
Allows you to take images through a telescope. Updated based in on remix by Jame_lan. ...Also made the boundary thicker to prevent light leak.
cults3d
Allows you to take images through a telescope. Updated based in on remix by Jame_lan. ...Also made the boundary thicker to prevent light leak.
prusaprinters
Shot with a small kit telescope, with a magnification of 35x, I was even able to see sunspots. Here's a timelapse of the eclipse through my phone <a href="https://youtu.be/1nUuXQIDXN8">https://youtu.be/1nUuXQIDXN8</a>.</p> <p>This adapter uses a new...
thingiverse
Shot with a small kit telescope, with a magnification of 35x, I was even able to see sunspots. Here's a timelapse of the eclipse through my phone https://youtu.be/1nUuXQIDXN8. This adapter uses a new screw mechanism compared to the old one from my...
thingiverse
... but insane steep overhang. So now you can print with layers >0.1mm (I used 0.15mm and I guess it will print fine with 0.2mm). ... The original design served me well for many images as you can see here: https://goo.gl/photos/fN794VnbNKKwXzdv7
prusaprinters
I made it a bit longer so that I could ease the printable but insane steep overhang. So now you can print with layers >0.1mm (I used 0.15mm and I guess it will print fine with 0.2mm). The original design served me well for many images as you can...