test lead holder 3d models

Simple test lead holder

Simple test lead holder, new version from my orignal test lead holder. Wall mounted, holds 1mm and 4mm test leads. This test lead holder has the same mounting hole distance (57.5mm) as the original version. It can also be mounted side by side to...

... ...You can fit your meter, generator and power leads on this hanger. Holes for wall mount or if not a lot of weight some two sided tape may work. Varied Width Test Lead Holder for scope probes, meter and generator leads along with skinny test clips

I needed signs for a few [test lead holders](https://www.thingiverse.com/thing:1412606), So I designed this model. ...It uses [fontmetrics](https://www.thingiverse.com/thing:3004457) for automatic length measurement of the text.

03/05/2017 - Updated version: http://www.thingiverse.com/thing:2153693 Just a quick test lead holder I made for the office to keep everything neat and tidy. Designed to fit 1mm and 4mm test leads Mounted on wall through two screw holes. Width:...

This was created out of frustration with the typical test lead holder that uses fingers, the test leads would fall off and it would take a while to figure out what was available from the rats nest underneath. ...This has resolved my issues and puts a...

Fluke TL175 test leads holder / reel Normally I wind up the test leads on the multimeter itself, but when you take out the multimeter from the toolbox to grab something else it would go loose and it is hard to reel up nicely. This is what I came up...

Here is a Test Lead holder for alligator leads and other small cables. It's perfect for all the cables and headset wires that clutter around your shop, desk or office. It also has a fillet at the right angle for added strength.&nbsp;</p><p>This is...

This is a holder for test leads and other cables. ...We use it in the MakerBot R&D lab to keep things nice and organized.

Hello, this is my version of a segmentary holder for laboratory test leads, based on the din-rail system. You can also use it for other cables of course. In this version the gaps between the elements is 4 millimeters. So if you have thicker or...

Need a place to hold your test leads? The spaces are 5mm apart, and I'll probably create more variations on this where they are farther apart for different sized cords. ... Very simple and not terribly elegant!

Summary Need a place to hold your test leads? The spaces are 5mm apart, and I'll probably create more variations on this where they are farther apart for different sized cords. ...Very simple and not terribly elegant!

... supplies and a multimeter but I also wanted the wires out of the way of the tool box. There is a 4 lead and 6 lead version I used these for the clips holding the wires before it gets to the lead holder: https://www.thingiverse.com/thing:2337726

This was designed to hold the test leads for my bench Multimeters and Oscilloscope leads. It could be used for any kind of cables. It slides onto Ikea type shelving. I have included one for a round shelf nosing and will add one for the square shelf...

This was designed to hold the test leads for my bench Multimeters and Oscilloscope leads. It could be used for any kind of cables. It slides onto Ikea type shelving. I have included one for a round shelf nosing and will add one for the square shelf...

Test lead holder for Electronics labs, designed to be wall mounted. ...Printed on Ender 3

Basic Test lead holder for cables up to 6.35mm (RG-6 with connector). You can fit your meter, generator and power leads on this hanger. Holes for wall mount or if not a lot of weight some two sided tape may work. All the STL files have been fixed...

3D printed holder for Oscilloscope and Multimeter (and Power Supply I guess) leads. ...Hangs the leads out of the way (and off your bench).

Use and like to keep most of my test leads in pairs, so I present test lead holder number 12xxxx

Customized version of https://www.thingiverse.com/thing:1102812 Created with Customizer! ...https://www.thingiverse.com/apps/customizer/run?thing_id=1102812

Customized version of http://www.thingiverse.com/thing:1412606 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1412606 Instructions Using the following options:...

Added mounting holes with strain relief -- use #10 panhead bolts or screws

Customized version of http://www.thingiverse.com/thing:1412606 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1412606

This is a set of test lead holders designed to clean up and organize the probes you use every day during electronics testing and troubleshooting. Each of the holders has dovetails to allow it to be mated on the left or right with any of the other...

Since many people seem to want a bolt-on cable holder that is more versatile than a box aluminum frame, we made one.This is reason why people want to … “The test lead folders on the market are for general use and have only screw holes. ”This version...

EN: Test lead holder and tip cover for Benning MM P3 multimeter DE: Messleitungshalter und Spitzenabdeckung für Benning MM P3 Multimeter

Customized version of http://www.thingiverse.com/thing:1412606 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1412606 Instructions Using the following options:...

This is a end stack-able cable holder. ...Connector pins and end caps are included. 4mm size is good for jumpers and test leads. ...Have fun.

... tape to the back to keep from scratching up the toolbox. I also enlarged the holes where the leads rest to 11mm to accommodate the larger Fluke leads. There are two versions one had the holes modified the other has the original size holes. ...

Customized version of http://www.thingiverse.com/thing:1412606 Created with Customizer! ...http://www.thingiverse.com/apps/customizer/run?thing_id=1412606